Refrigerant vapor rejects 70 kW ofheat as it passes through an air-cooled condenser. The condenser hasan air-side area of 210 m2 and basedon this area, has an overall heattransfer coefficient of 0.037kW/m2.°C. Cooling air flows at a rateof 7.59 kg/s. If condensation of therefrigerant occurs at 55°C, what is theoutlet temperature (in °C) of the air?Take the specific heat of air to be 1.02kJ/kg.°C.

To determine the final temperature of the air through the condenser, we must use the concept of heat…

Answered: ketrigerant vapor reje neat as it…

ketrigerant vapor reje neat as it passes through an air- cooled condenser. The condenser has an air-side area of 210 m2 and based on this area, has an overall heat cransfer coefficient of 0.037

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The clean U for an exchanger is 800 BTU/(hr 0 F ft2). Its tube area is 600 ft2. After operating for several months heating water from 50 0F to 160 0F at a flow rate of 210 GPM with a heating fluid on the shell entering at 290 0F and exiting at 160 0 F has the overall U decreased significantly?
The food storage room requires a cooling system with a capacity of 10 tons of refrigeration which operates at an evaporator temperature of -17.8 degrees Celsius and a condenser temperature of 30.1 degrees Celsius. The activities used are R-717 and the operating system is in saturated conditions. Determine a. Flow rate b. refrigerant flow rate c. rate of heat loss in the condenser.
Can you also show the plot on the chart provided? The mass flow rate of the refrigerant in a Single Stage Vapor Compression (SSVC) refrigeration system is 0.015 kg/s and the evaporating and condensing temperatures shall be -20°C and 50°C, respectively. Determine the following: (1) cooling capacity in tons, (2) work of compressor in kW, (3) COP of the system, (4) EER of the system, and (5) refrigerating efficiency. Can you also show the plot on the chart provided?
Catalogue data of a water-cooled condenser of a manufacturer gives the following details: Condensing temperature 48.9°C Water inlet temperature 37.8°C Water flow rate 20.694 kg/s Capacity 145 tons Estimate the capacity of this condenser with the same water flow rate but with an inlet temperature of 30°C and a condensation temperature of 42°C. The evaporation temperature may be assumed to be constant at 2.2°C.
Calculate the mean condensing heat – transfer coefficient when refrigerant 12 condenses on the outside of the horizontal tubes in a shell – and – tube condenser. The outside diameter of the tubes is 19 mm, and in the vertical rows of tubes there are, respectively, two, three, four, three and two tubes. The refrigerant is condensing at a temperature of 52°C, and the temperature of the tubes is 44°C. Please refer for the table below.
11 MWth plant operates at a thermal efficiency of 34%. The waste heat is dumped across a condenser which operates at a shell side pressure of 0.717 psia. For the given information below, determine the condenser tube length. A Coolant Flow Rate 4.81 x 108 Ibm/hr Coolant Inlet Temperature 60 F Number of Tubes 62,832 Lattice triangular Pitch 1.5 inch Tube OD 1 inch Tube ID 0.944 inch Tube Thermal Conductivity 10 Btu/hr-ft-F Condensing Heat Transfer Coefficient 1228 Btu/hr-ft²-F
27. Air is being heated with steam in a heat exchanger as shown in following fiqure. Saturated water opy yer vapor enters this unit at 35°C at a rate enters the unit at 20°C, and leaves at 30°C at same twarie, process. 10,000 kg/h and leaves as saturated liquid at Marut, iwarr Air generation associated with Determine the rate of MarutPrewari Air 20°C 32°C Steam 35°C 10,000 kg/h Marut Tiwari 30°C Marut Tiwari
ROOM (2) 700kPa x-0 CONDENSER k (1) 40°C 700OkPa EXPANSION VALVE (3) 100kPa EVAPORATOR (4) 100kPa x=1 OUTSIDE Consider a heat pump cycle operating with R134-a fluid at 0.01kg/s mass flow rate. Conditions are given in the figure. a) What are the values of heat supply rate to the room and heat absorption rate from the outside? b) What is COP of this heat pump? c) Assume we immediately put a watermelon of 8kg to the room at 2°C. Assuming a specific heat of 4200J/kg for the watermelon, how long will it take for the watermelon to reach room temperature of 20°C if we assume that heat pump only heats watermelon? CA122.minutes O D112 menute COMP.
20,000 lb/hr of air is to be cooled from 150°f to 100°f by water flowing in a shell-and-tube heat exchanger. cooling water is available at 70°f and should leave the exchanger at 95°f. available to do this cooling assignment is a one-shell pass, two-tube pass exchanged consisting of fifty 1-in OD 18 BWG copper tubes, each 10 ft long. the tubes are arranged inside a 10-in shell on a staggered 1-1/4- inch triangular pitch with baffles spaced every 6 in. is this exchanger satisfactory?
Hot air at 40 ° C and RH 65% is heated using a heat exchanger to reach 90 ° C. Using a psychrometric chart, determine:a) the amount of heat added per 2 m³ of initial air = ... (kJ) b) condensation temperature = ... (° C)
Problem: An ammonia refrigerating system shown in the figure is composed of three evaporators and arranged with multiple expansion valves and intercoolers. The load and operating temperature of each evaporator are shown in the table below: condenser evaporator 3 compressor 3 intercooler 2 evaporator 2 compressor 2 Infercooler 2 liquid evaporator 1 compressor 1 Evaporator Load, tons Evaporator Temperature, °C 1 30 - 30 20 - 20 15 - 10 Condensing pressure is 1200 kPa. Refrigerant vapor exits evaporator no. 1 with a 10 - degree superheat. Saturated conditions exist at the exits of the evaporator no. 2 and evaporator no. 3. Liquid refrigerant leaves the condenser at 28°C. Determine a. the mass flow rate in evaporator 1 kg/s b. the mass flow rate in evaporator 2 kg/s c. the mass flow rate in evaporator 3 kg/s
A straight-condensing 10,000 kW turbine has a guaranteed steam rate of 5.90 kg/kW.hr when exhausting at 5.0 kPa. Exhaust steam enters the condenser at 92% quality, and it is estimated that fouling will decrease the overall coefficient by 30% during operation. Cooling water is available at 18 ℃, and for design purposes, 1 ½ in OD 16 BWG Brass tubes (thickness = 0.065 in, k=62 BTU/hrftF°.) are specified with 9 C° rise in cooling water, which circulates at 5 ft/s. Inside and outside film coefficients are hi=960 and ho=1474 BTU/hrft2F°. Design a condenser for this turbine, considering tube and boundary resistance as flat surfaces and neglecting any crossflow factor. Determine the followinga) Effective overall coefficient of heat transferb) Volume flow rate of cooling waterc) Number of tubes for single passd) Length of tubes