K B D E F F1 F4 Fs

Q: The square gate AB is held in the position shown by hinges along its top edge A and by a shear pin…

A: d=4.5 ftArea of gate=1.8*1.8density of water,

Q: 2. The bracket BCD is hinged at C and attached to a control cable at B. For the loading shown in…

A: To find : determine the tension in the cable and the reaction at C.

Q: Structure type #1 Find the internal forces in each member of the truss A * 35 8 15 Jo * O 15 d N X…

A: Find the internal forces in each member of the truss.

Q: Period: This bridge spans a 10ft wide creek. A 30lb downward force is located at the top center of…

A: To Find :  The x and y components, what is the load and the T or C for each member. Given:  The load…

Q: I just need the answers to 1,2,3. 1.The problem sketch shows _____ loads. 2.The moment load (the…

A: For the given arrangement  condition- The resultant of two forces is in vertical

Q: Use the method of sections to determine the forces in members BD, CD, and CE. Note: The support…

A: Given data  Given truss system

Q: 300 lb./ft. 9 ft. 600 lb./ft. 5 ft. 200 lb./ft. B 7 ft. 1000 lb.

A:

Q: AF, = 153 N load and a F2 = 99 N are applied to the frame which is supported by pins at A and B.…

A:

Q: Find the forces developed at pins E. 4 kN/m

A: Given

Q: Compute the moment arm for the force in cable C, measured relative to the AB axis. Use d₁ = 3.5 ft,…

A:

Q: 1) Use the method of PINS to determine the true magnitude and direction of the forces in all the…

A: please refer handwritten solution

Q: For the truss shown, find the magnitude of the force F BE using the figure and the given data. F₁ =…

A:

Q: Calculate forces (moments if applicable) for all points shown and write them down in a table.

A:

Q: Learning Goal: Use the general equations of motion for plane motion to determine the initial…

A:

Q: Determine the force in each member of the space truss given F-3 kN. Use positive to indicate tension…

A: Ans Given Now the coordinates of various point areNow calculate the unit vector along AD asAgain…

Q: The truck shown is used to deliver food to aircraft. The elevated unit weighs 2400 lb vwith center…

A:

Q: TRUSS PROBLEM Determine: a) The magnitude and direction of the reactions at 3 and 5 b) The forces…

A: To find - a) The magnitude and direction of the reactions at 3 and 5. b) The forces in each member…

Q: Determine the magnitude and sense of the forces in bars A and B in the figure shown below. Show all…

A: Given data, A 80 k downward force is acting in a junction of bar A and B. To determine:- The…

Q: The spring AB has an unstretched length of 252 mm and stifness k=842 N/m. In the configuration…

A: Lo=252mm=0.252m K=842 N/m L=576mm=0.576m   To find: FBD

Q: Determine the magnitude of the forces. In the given figure, V = 300 N, V2 = 1.6 m, and V3 = 11 m.…

A: V1=300NV2=1.6 mV3=11mconsidering FBD of joint Cconsidering force qulibirium along x dirction…

Q: Three hydraulic cylinders control the motion of the backhoe arm and bucket in the given figure. In…

A:

Q: All members of the truss have the same length. NOTE: This is a multi-part question. Once an answer…

A:

Q: dimensions, L1 = 6.8 in and L2 = 3.3 in, determine the polar moment of the weld about its centroid.…

A: