The truck shown is used to deliver food to aircraft. The elevated unit weighs 2400 lb vwith center of gravity at G. Determine the required force in the hydraulic cylinder AB. The force is positive if in tension, negative if in compression. 52" 16" 68" G D.

The truck shown is used to deliver food to aircraft. The elevated unit weighs 2400 lb vwith center of gravity at G. Determine the required force in the hydraulic cylinder AB. The force is positive if in tension, negative if in compression. 52" 16" 68" G D.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.26P: The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A...

See similar textbooks

Related questions

Q: Answer the following

A: Given data: The specific gravity of oil, (SG)oil = 0.85. Density of water, ρw = 1000 kg/m3. The…

Q: Three boards were suspended in three ways which of the following options is correct for tensions…

Q: 4. Two liquids of different densities p= 1500 kg/m³ and p= 500 kg/m³ are poured together into a…

A: Given: The density of two liquid is ρ1=1500 kg/m3 and ρ2=500 kg/m3. The volume of tank is V=100 lt1…

Q: A conical tank having a radius of the base equal to 0.27 m and a height of 0.8 m. The cone is laid…

Q: PROBLEM 2 The elements of a floor jack are shown in the figure. If the hydraulic cylinder AB is…

A: Given DataFAB=37kNTo findL=?FEF=?FC=? ***As per our company policy we are supposed to do only three…

Q: Answer the following

A: Draw the free-body diagram of the reach-stacker with the arm.

Q: 1. Why engineers are considered a significant segment of society?

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: . A piston rod, made of AISI 3140 steel, OQT 1000 F, is subjected to a repeated, reversed load. The…

A: Given Su=152.5 ksi Sy=132.5 ksi Nu=8 Ny=4 a) Based on ultimate strength…

Q: 2. A square hollow steel strut with a wall thickness, t, = 10 mm is pin connected to two gusset…

Q: The crank of a reciprocating engine is rotating at 300 rpm. The lengths of the crank and the…

Q: A four bar linkage have the following dimensions. Fixed Link AD = 4m, Driving Link AB = 1.5m, Driven…

Q: Answer the following

A: Given data The initial temperature of the bar is T1=72°F The final temperature of the bar is T2=0°F…

Q: Solve for the reactions at point A. A 9.33 KN B. 10.33 KN C. 11.33 kN 3m B D E -2 m2 m-2 m--2m--2m-2…

A: Given data: The distance between AB, BC, CD, DE, EF and FG is x = 2 m. The force acting on joint B…

Q: Please give the answer as in the format asked

Q: instantaneous discharge velocity

A: Given; Large tank with a nozzle attached contains three immiscible, inviscid fluids as…

Q: 3. The 2-kg collar is at rest in position A when the constant force P is applied as shown. Determine…

Q: 1. What are the procedures on how to calibrate a water tank? (At least 10 steps) 2. What are the…

A: 1) To find: The procedures to calibrate a water tank.

Q: Determine the specific volu ideal-gas equation of state

Q: A rigid strut ABCD supports two concentrated loads P at points B and D. It is being supported by a…

A: Given: The area of cable, A = 120 mm^2 = 120 x 10-6 m2 The elastic modulus of the cable, E = 50 GPa…

Q: 3. Given the following data of the figure shown : P= 3.5 KN, L, = L, = L, = 1.5 m Strut BC = 100 mm…

Q: A jet of water 50 mm in diameter and a plate strikes each at a right angle. When the plate is moving…

Q: The following data was recorded during a test performed on a steam plant consisting of a Lancashire…

A: To Find: Factor of evaporation (Fe) and overall efficiency of the plant η Given that, ms=5000…

Q: A certain amount of an ideal gas is initially at a pressure p, and temperature T,. First, it…

Q: Answer the following

A: Given, E=30,000,000 psi, G=11,500,000 psi

Q: 3.6. A short compression member with Do = 2Di is to support a dead load of 25 tons. The material is…

A: Given data: The dead load is F = 25 tons. The factor of safety is FOS = 2. The yield strength is Sy…

Q: Determine the shear force V in the beam at the point located 0.60 m to the right of point B. The…

Q: A turbopump features the characteristic diagram reported below and operates at Q= 500 m /h. Evaluate…

A: The data corresponding to 500 m3/h flow rate from the graph is

Q: Please answer the following

A: Given data DAB=30 mmDBC=46 mmdAB=10 mmdBC=25 mmTAB=10 N·mTBC=20 N·m

Q: 5. Determine the moment of the 360N about a) point A, and b) point B 360 N 40° 100 mm 225 mm A 25•…

A: Given data: F=360 N Need to determine the moment about the point A and B.

Q: A liquid-level system has the following properties: Tank dimensions: 10 ft high by 5-ft diameter…

A: Given : To find : Liquid level

Q: The ramp is used as passengers board a small commuter airplane. The total mass of the ramp and six…

Q: PROBLEM 1 The platform scale consists of a combination of third and first class levers so that the…

A: Given, L=120kg, S=3kg, g=9.806m/s^2

Q: The 0.25 kg slider A is pushed along the circular bar by the slotted bar. The circular bar lies in…

Q: Q6 Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke…

Concept explainers

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.

Question

100%

give a answer to 3 decimal points

The truck shown is used to deliver food to aircraft. The elevated unit weighs 2400 lb with center of gravity at G. Determine the
required force in the hydraulic cylinder AB. The force is positive if in tension, negative if in compression.
52" 16" 68"
53"
E
53"
AB =
i
Ib

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The truck shown is used to deliver food to aircraft. The elevated unit weighs 2350 lb with center of gravity at G. Determine the required force in the hydraulic cylinder AB. The force is positive if in tension, negative if in compression. 46" 18" 64" Answer: AB= G D 70" 70" lb
It is desired that a person be able to begin closing the van hatch from the open position shown with a 10-lb vertical force P. The center of gravity of the 90-lb door is 1.5 in. directly below point A. Treat the problem as two-dimensional. Determine the necessary force in each of the two hydraulic struts AB. Express your answer in units of lb. A P 45" A B 22" 24" Hinge axis 6.5" 30° B Strut detail
In the equilibrium position shown, the resultant of the three forces acting on the bell crank passes through the bearing O. Determine the vertical force P. Does the result depend on 0? 48 lb 6" 75 lb Answer: P = i 6" 15° $ lb
6.62 Neglect the mass of the pulleys and the link. The block has a weight of 230 lb and the cord is attached to the pin at B. The pulleys have radii of r1 = 2 in. and r2 = 1 in. Determine the force P on the cord. Determine the angle θ that the pulley-supporting link AB makes with the vertical.
30 cm 18 cm Hom Scm Hom Sum 2. The 30 cm handle is connected rigidly to the 5cm bar at a right angle. Determine the force developed at A if a force P = 100 N is applied perpendicular to the handle when the handle is at the position indicated.
the tree feller cuts off large trees near ground level and then continues to grasp the trunk. Determine the force in hydraulic cylinder AB for the position shown if the tree weighs 6000lb. Determine the required pressure on the 4.72-in.-diameter piston of the cylinder. draw the free body diagram
Determine the internal force on: Member AC
The L-shaped rod AOCD has an 80 kg mass hanging from it at B. The rod is leaning against a smooth wall at A. Point B is half way up OA. There is a journal bearing at C and a thrust bearing at D. They are properly aligned. A force F is pulling in the x-direction at B. Just as the rod comes off of the wall at A, what is the magnitude of the force F. 1 m B F 1m
(Please show magnitud and direction for every member forces) Use the method of MEMBERS to determine the true magnitude and direction of the forces in members1 and 2 of the frame shown below in Fig 3.4.
5. The machine part of negligible weight is supported by a pin at A and a roller at C. Determine the magnitudes of the forces acting on the part at A and C. Ne 50 400 2.4 kN-m 40/ 24 KN-m 407 -200-250- -300 13 kN 200 250 300- 3 kN Dimensions in mm FBD
The shear leg derrick is used to haul the 162-kg net of fish onto the dock. Determine the compressive force along leg AB. Assume the force in each leg acts along its axis. Supply the answer in kN and as a negative number. Add your answer 4 Additional content You can add text, images, and files here. PELL 5.6 m 4 m R
3