--K- 3 m/s Baelish was too shy to give his gift to his friend, Sansa, so he made a contraption out of a 1 m- radius gear L, a 1.2 m-radius gear I and a 0.5 m-radius cylindrical spool of rope K. The spool K was glued and is concentric to gear I. He skillfully rotated gear L causing it to have a constant angular acceleration. Starting from rest, gear Lrotated a total of n/3 radians right before the speed of box E became 3 m/s. At this instant, b. What are the angular velocities of gear L and I, w and wi? c. What are the angular accelerations of gear L and I? 2.

--K- 3 m/s Baelish was too shy to give his gift to his friend, Sansa, so he made a contraption out of a 1 m- radius gear L, a 1.2 m-radius gear I and a 0.5 m-radius cylindrical spool of rope K. The spool K was glued and is concentric to gear I. He skillfully rotated gear L causing it to have a constant angular acceleration. Starting from rest, gear Lrotated a total of n/3 radians right before the speed of box E became 3 m/s. At this instant, b. What are the angular velocities of gear L and I, w and wi? c. What are the angular accelerations of gear L and I? 2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The distance between two parallel shafts is 20 mm and they are connected by an Oldham's coupling. The driving shaft revolves at 160 rpm. The maximum speed of the intermediate piece along its groove is
3. The 40.64 cm. diameter pulley of a gasoline engine is connected by a belt (which is assumed not to slip) to the pulley of the pump. The belt speed is 1200 m. / min. Determine (1) the angular speed of the engine pulley in RPM and in rad / sec. and the diameter in cm. of the pump pulley if the pump speed is one-half the speed of the engine pulley.
$16-77 16-77. The planetary gear system is used in an automatic transmission for an automobile. By locking or releasing certain gears, it has the advantage of operating the car at different speeds. Consider the case where the ring gear R is held fixed, wR = 0, and the sun gear S is rotating at @R @s = 5 rad/s. Determine the angular velocity of each of the planet gears P and shaft A. WR R 20.000 32 C ws 40 mm st 80 mm 40 mm Prob. 16-77 A
I'm trying to understand this problem is there an easier way to solve other than the the solution I attached? That just doesn't look like a relative acceleration equation it is so complicated any help is so appreciated thanks.
Problem 2 The DESS SOCIO are studying a planetary gear system. The outer gear ring is stationary. A motor that is 80% efficient drives bar 0.3-kg bar AB which in turn drives 0.6-kg gear B. The electrical input power to the motor is 0.1 kW. The bar AB rotates at 120 rpm counterclockwise at the position shown. Determine the angular velocity of gear B when bar AB is rotated by 90 degrees. Assume a constant torque from the motor. M 0.10 m 0.050 m
A, B & C please. Thank you!
5
(please solve within 20 minutes i will give thumbs up thanks) hand written
The first answer for this problem was incomplete and the answer was cut off so if anybody can complete the solution please? thank you very much.
Please give me all a, b and c solutions..
Need asap please
Two gear wheels with 50 and 30 teeth respectively, mesh externally, the speed of the smaller being 1800 r.p.m. Determine the velocity of sliding between the gear teeth faces at the point of engagement, at the pitch point, and at the point of disengagement if the smaller gear is the driver. Assume that the gear teeth are 18° involute form, addendum length is 8 mm and the module is 5 mm. Also find the angle through which the pinion turns while any pairs of teeth are in contact. answer with clear word please.