Figure 1 shows a pulley system that consists of three blocks of A, B and C. Block B starts from rest, whilst block A moves upward with a constant acceleration, and slider block C moves to the right with a constant acceleration of 60 mm/s?. Block B and C moves with a velocity of 360 mm/s downward and 160 mm/s to the right, respectively, a) Determine the accelerations of block A and block B at t=4 s? b) Determine the initial velocities of block A and block C at t 4 s? c) Compute the distance of slider block C moves after t=5 s? B

Figure 1 shows a pulley system that consists of three blocks of A, B and C. Block B starts from rest, whilst block A moves upward with a constant acceleration, and slider block C moves to the right with a constant acceleration of 60 mm/s?. Block B and C moves with a velocity of 360 mm/s downward and 160 mm/s to the right, respectively, a) Determine the accelerations of block A and block B at t=4 s? b) Determine the initial velocities of block A and block C at t 4 s? c) Compute the distance of slider block C moves after t=5 s? B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Don't give copied solution. I need correct solution with full explanation
Based on the table below, which of the statements below is/are correct regarding the 3D printing process shown in the schematic? a.You can produce a room-temperature non-fragile 225C oven-safe food container with at least one material from the above table using this process and a 280C nozzle b.You can use this process to print plastic or brittle objects but not elastomers and rubbers c.Manufacturing a thermoplastic HDPE hose with an extrusion nozzle heated to 175C is possible with this process d.You can print thermoplastic and thermoset polymers with this process, you only need to make sure that the nozzle specs and the crosslinking conditions match the polymer requirements e.This process is best suited for the low volume production of tubes, bars and beams due to the nature of the extrusion process
8)
In the textbook (Fundamentals of Modern Manufacturing Materials, Processes,and Systems 7th Edition by Mikell P. Groover) chapter 4 problem 8, I’m having trouble trying to understand and solve the problem with the information given to me. Image below.
Company XSheetMetal Ltd. is mass producing the component illustrated in Figure 1. 90 R0,5 0,5 Figure 1 (All dimensions in mm) Page 5 of 5 b) As a process planner within this company what type of tools and machines would you require to manufacture this part?
Q33) Write the appropriate names against the components shown in FIGURE 17 FIGURE 17 Page
Multiple choice questions, please help thank you!! 1. The chemical potential (μ) of smaller size clusters is bigger than that of bigger size clusters because of (a) their small size (b) the fewer number of atoms in them (c) surface area is smaller (d) their surface is more curved 2. Which of these characteristics would you associate with SEM: A surface imaging tool Maintained under vacuum Provides imaging and compositional data Uses a scanned electron beam All of the above 3. Secondary electrons (SE) are best described as Low energy electrons from the sample surface High energy electrons from the sample surface Low energy primary beam electrons High energy primary beam electrons 4. Atomic force microscopy (AFM) is the most widely used form of scanning probe microscopes for the characterization of nanomaterials since it require: (a) electrically conductive and optically transparent samples (b) neither electrically conductive nor optically transparent samples (c) electrically…
5 Explain the “4C’s” practised as part of current Good Manufacturing Practice (cGMP) to prevent cross - contamination
a) Explain the functions of a plastic coatings. b) Assume you are a Mechanical engineer working in Al Jazeera Steel Company LLC is situated in Sohar. You are assigned a task to setup the system to coat the surface of the hot component dipped in oil. For example the dark blue colour steel gun is shown below. Based on the above scenario, answer the following questions. i) Suggest the suitable surface coating process. ii) Explain the above surface coating process in detail.
(c) Explain critical point and triple point with suitable example.
Can you show me the equations and the calculations to get the red values in the image?