JFET transistor was used in RC coupled amplifier (CS bypass - voltage divider) with internal source signal resistance 25 ko,gate resistance 2MA, source resistance 8KN, drain resistance 8KC2, load resistance 2KC. The data sheet gives: gm = 12 mS,gate-source capacitance 8 pF,feed-back capacitance equals to 40 pF,and Cw. =15 pF.Assume coupling capacitors 10aF ,and bypass capacitor 32 uF. a) Determine the effective upper (higher) critical frequency applving Millers theorem

JFET transistor was used in RC coupled amplifier (CS bypass - voltage divider) with internal source signal resistance 25 ko,gate resistance 2MA, source resistance 8KN, drain resistance 8KC2, load resistance 2KC. The data sheet gives: gm = 12 mS,gate-source capacitance 8 pF,feed-back capacitance equals to 40 pF,and Cw. =15 pF.Assume coupling capacitors 10aF ,and bypass capacitor 32 uF. a) Determine the effective upper (higher) critical frequency applving Millers theorem

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

SV What is clocking block ? what is program block?
11. What is the configuration of the given amplifier circuit below?12. How are the coupling capacitors treated in the figure of #11 at AC?
1:- For the emitter bias circuit shown in figure(1), if Vec-20V, B-50, RC-2k2, RB-430k2, and RE=1kQ. Vee (a) Determine IB, IC, and IE. (b) Determine VCE, VC, VE, VB. RB (c) Draw the de load line. Vo (d) The stability factor SICO. vì For the amplifier
For the BJT circuit shown below, sketch the hybrid equivalent model circuit with labels of voltages, impedances, and currents. ... 1.8k0 Vo 39ka 22ko tuF-POL 10UF-POL 1200 1uF-POL 2N2221 100mv 1.5KHZ ODeg
III An n-channel MOSFET ID versus VDS set of characteristics is shown below. A common-source resistively loaded amplifier uses this MOSFET. The resistive load RL = 1,000 ohms and the drain power supply (VDD) = 3 volts. (a) Draw the load line over the l-V characteristics shown immediately below.. (b) What is the slope of the resistive load line? VDD =3 volts 6 mA 5 mA -+ R. 4 mA + 3 mA -t 2 mA 1 mA 3 V 4 V 5 V Vps
Data sheet below shows design parameters for a Common Source FET Transistor amplifier.VDD = 12V , VD = 0.75 VDD , VG = 0.5 VDD , Cin = Cout = 5muF , K = 1mAV-2 , VTN = 1V , R2 = 10k and ID = 2mA Q. At DC condition,design the circuit by calculating values for VG,R1,RD,VGS,RS and gm of the FET amplifier (show all the calculated steps involved). Propose and draw the DC circuit from the calculated values.
In an emitter-biased transistor circuit, we have collector source voltage V CC = 15 V, collector resistance RC = 3.5 kOhm, emitter voltage V_E = 4.3 V and emitter current LE = 2.1 mA. If the current gain is 150, what is the difference in emitter-collector voltage V_CE when we calculate it including the gain factor vs when it is calculated by assuming collector current LC = LE? Select one: O a. 3.35 V O b. 3.40 V OC 0.05 V O dov
Derive the output resistance using small signal model for the following circuits, assuming the transistor has output resistance of a transistor is ro and transconductance of gm. Rout PPA Rout Vb- Vbo Rout Rout Vdd Vb- Rout
Design a common emitter amplifier for a Vout of+-6.3V. Vcc is set to 9V. At x=1, Av=12.6 V/V and the dynamic range from 6.3V to -6.3V. Rout must be less than 100 ohms and Rin must be higher than 100 kohms
What are resistors for? What are capacitors for? What are transistors for? What are Operational amplifiers for? What are oscilloscope for?