IVI ude remains

Q: . When SW2 is closed, the motor will spin and D1 will light. The current through 1.______ will flow…

A:

Q: Look at the diagram and answer the following questions

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: ectrician A says that a circuit breaker marked 120/240 V is acceptable for a circuit that doesn't…

A: Answer: B.  Electrician A is correct

Q: The lengths of two discrete time sequence x₁ [n] and x2 [n] are 1 and 6 respectively. The maximum…

A: We need to find out the length of output for given convolution .

Q: Sent Mail - fatimaoctober09eg x + Vw/0/Bsearch/akm/FMfcgzGmthgmlPbPzrGgcwkqLIvFcbSF?projector=1 O…

A:

Q: Elimination of armature reaction requires a series field winding True False

A: Answer is True    Interpoles are similar to the main field poles and located on the yoke between the…

Q: The type of the lamp in the below picture is Select one: O Bayonet cap O. Bayonet Screw O Edison cap…

A: In the shown in the figure Which type of the lamp in the figure

Q: What size ungrounded conductors does a 150 A residential service require? a. 2 AWG b. 1 AWG c. 1/0…

A: The correct option could be b and d also because you didn't mentioned which Conductor when it's…

Q: What is the dimensioning system shown in the figure below? +1.31 67 .31 .51

A:

Q: 12. To read and understand electrical blueprints, you need to know A. how to sketch a plan view.…

A: Given To specify What is important to read and understand electrical blue prints.

Q: Question 5- Power Network, Frequency & Connected Load a) In the UK and many other countries, there…

A: The legal requirement to maintain the voltage and frequency with permitted tolerances is due to the…

Q: Can you please redo this. The answer is incorrect.   Also, be sure not to round until the very end…

A:

Q: number 2 also please

A:

Q: What is the area of ​​the shaded part

A:

Q: Determine the resistance of the resistor using resistor color coding. *

A:

Q: Can you please circle the answer of questions c and e because iits complicated

A: The above question is based on the root locus.

Q: Give the value of the following resistors: with solutions (Must write final value to short notation…

A:

Q: 3List out common electrical hazards and give risk level for each of them

A: 1. discharge of current through insulating materials: If the appliance is not connected through an…

Q: Only correct answer with diagrams

A: Given Data:A stranded conductor with,Side of the reference pentagon Number of strands n=5To…

Q: Determine Reg in Ohms at the (a,b) terminals for the following circuit. Round your answer to the…

A:

Q: Problem 1 is a review of your understanding of KVL (Kirchhoff's voltage law) Using KVL find the…

A: A simple question based on network analysis and the topics described in the solution are kirchoff's…

Q: 5- An instrument is used for lowering the value of voltage for measuring and protection is a.…

A: The objective is to determine the correct option for the given statements.

Q: What are unit system of protection

A: Switchgear protection :- It is very important for modern power system network. It protects system…

Q: Write a program to shows how you can use PB0 and PB1 to control the current flow in the bi-color LED…

A: The Answer is

Q: Z Look at the graph in figure 4 and complete the gaps in the text with a preposition from the box.…

A: Given  Fill in the blanks using the preposition table given. Please find the below attachment.

Q: Parallel conductors must be installed in sizes no smaller than A. 1/0. B. 2/0. C. 750 kcmil. D. 4/0.

A: Given To determine minimum size of conductors  that must be used in parallel conductors

Q: Which of the following-combinations cannot be combined into K-map groups?   A. corners in the same…

A:

Q: Describe the importance of safety management to avoid physical injury in electrical work. QI (a) (i)…

A: Electrical hazard- Electrical hazard is any electrical appliance or system that has the potential…

Q: Say that you are given some TPWM and some number of intervals N to specify TON. If TPWM doubles…

A: PWM -Pulse width modulation is a technique that varies the ON/OFF time of a waveform. T PWM =The…

Q: Please solve question 3 in the same way thank you

A: Given:we need to find the z-transform of the signal x[n] using standard pairs of z-transform and…

Q: . Review. The heating element of an electric coffee maker operates at 120 V and carries a current of…

A: Given,  Voltage (V) = 120 V Current (I) = 2 A Mass of water (m) = 500 grams Initial temperature (T1)…

Q: Lenz law Explain please written

A: In this question we discuss about Lenz law

Q: Determine the voltage dropped on R3

A: In this question, we need to determine the voltage across the resistance R3  as shown in circuit. We…

Q: Vdc0 U=12 V Circuit #1 Ried LED www Ried_series Vdc0 U= 12 V Current in LED (A) Circuit 0.03 #₂ 0.02…

A: Given Data:An LED illumination circuit with,Supply voltage Set-current of the diodes V-I…

Q: C.T. and P.T. are used for _________ Group of answer choices measuring high currents and voltages…

A:

Z parameter

The Z-parameters that are the impedance parameters of a two-port network are defined by expressing the two-port voltages V1 and V2 in terms of two-port currents I1 and I2. The Z-parameters are calculated by open circuiting one of the two ports at a time henceforth they are called open-circuit impedance parameters.