Items produced in an industrial process can be dassified as either defective or non defective. The probability that an item is defective is 0.1. An experiment is conducted in which 5 items are drawn randomly from the process. Let the random variable x be the number of defective items in this sample of five. Determine the probability mass function f(x).

Items produced in an industrial process can be dassified as either defective or non defective. The probability that an item is defective is 0.1. An experiment is conducted in which 5 items are drawn randomly from the process. Let the random variable x be the number of defective items in this sample of five. Determine the probability mass function f(x).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A textile fiber manufacturer is investigating a new drapery yarn, which the company claims has a mean thread elongation of 12 kilograms with a standard deviation of 0.5 kilograms. The company wishes to test the hypothesis H0: µ = 12 against H1: µ < 12 using a random sample of n = 4 specimens. Calculate the P-value if the observed statistic is x = 11.5. Round your final answer to five decimal places. Show all the necessary solutions. P-value: Blank 1 Blank 1 Add your answer
3.4 The load on a cantilever beam of length L consists of a load Pat the tip (free end) and a distributed load wacting over the entire length. Both Pand ware random variables. The length is assumed to be deterministic, and its value is 6 ft. The statistical parameters of Pand ware as follows (1 lb = 4.448 N; 1 ft = 0.3048 m): Hp = 4000 lb Hw = 50 lb/ft Vp = 10% Vụ = 10% %3D A. Calculate the mean and standard deviation of the internal bending moment at the fixed end. B. Calculate the mean and standard deviation of the internal shear force at the fixed end. C. If both Pand w are normal random variables, what is the probability that the bending moment at the fixed end will exceed 29 k-ft (1 k-ft = 1.356 kN-m)? D. If both Pand w are normal random variables, what is the probability that the shear force at the fixed end will exceed 5000 lb?
Two parts are assembled as shown in the figure below. Assume that the dimensions x and y are normally distributed with means µ¸ and µ¸ and standard deviations σx = 0.4 and oy = 0.3 respectively. The parts are produced on different machines and are assembled at random. (a) If it is desired that the probability of the clearance (i.e., x - y) smaller than 0.09 should be 0.006, (i.e. Pr{(x-y)<0.09} = 0.006) What value of (x − μy) should be specified? - (b) Based on the results (x-µy) obtained in (a), calculate the probability that the clearance is greater than 0.
tb = (16.67 - 11.11)9.81(0.15 + 0.05) how did the answer became 2.83? when multiplied the following the answer is 10.32?
The mean average of the numbers a, b, 8, 5, and 10 is 6, and the variance is 6.80. What set of the given numbers a and b that agree to the given mean average value and the variance of the population? i: a=0, b=7 ii: a=5, b=2, iii. a=1, b=6, iv. a=3, b=4 Subject: Applied Statistics
3.. The manufacturer of a patent medicine claimed that it was 90% effective in relieving an allergy for period of 8 hours. He then proves this claim by selecting a simple random sample of allergy patients. To test the legitimacy of the manufacturer's claim, what test of hypothesis should we use? O A. One sample t-Test O B. Two sample t-Test for paired samples O C. Two sample z-Test for proportions D. One sample z-Test for proportions
6. It has been determined experimentally that steel wires of a certain length have strength with a mean value of 1 kip and a coefficient of variation of 16%. What is the probability that the strength of such a wire is less than 0.7 kips? Try Type I and Type III asymptotic distributions of extremes and compare the results. Given: x* = e* k! k=0 8.
Samples of sizen=5 are taken from a manufacturing process every hour. A particular quality characteristic, which is normally distributed, is measured, and X-ba and R calculated for each sample. After 25 samples, we have the following sums: the sum of X-bar values =662.5 the sum of R values=9.0 a) Find the control limits of the X-bar and R-charts. b) Assume both Charts exhibit "in control " behavior. If process specifications are 26.40 plus or minus 0.30, estimate the fraction nonconforming. c)If the mean of the process were adjusted to exactly 26.40, what would be the new fraction non-conforming?
Measurements of the flexible strength of carbon fiber are carried out during the design of a leg prosthesis. After 15 measurements, the mean is calculated as 1725 MPa with a standard deviation of 375 MPa. Previous data on the same material shows a mean of 1740 MPa with a standard deviation of 250 MPa. Use this information to estimate mean and standard deviation of the posterior distribution of the mean. Note: round your answers to only 2 decimals. The mean value of the posterior is type your answer. MPa and the standard deviation is type your answer. MPa.
Could you please solve the follwing question? Start the solution by Assuming a value of f to calculate the corresponding D
A concrete factory produces ten types of concrete products shown in the table below. The concrete products have the same standard deviation but different mean weights. Accordingly, the concrete product type (3) has the least relative variation. * Concrete 1 2 3 6 9 10 Products Mean 150 300 375 160 325 270 160 275 165 275 weight (Kg) 5n 4.
For computing the variance this number is called as the value that is added or subtracted from the most probable value. O a. Error O b. Accuracy c. Probable Error d. Mistake Clear my choice