It was observed that the difference of heads between the two ends of a pipe 300m long and 0.25 m diameter is 1.8 m. Taking Darcy's friction factor as 0.01 and neglecting minor losses, calculate the discharge flowing through pipe.

It was observed that the difference of heads between the two ends of a pipe 300m long and 0.25 m diameter is 1.8 m. Taking Darcy's friction factor as 0.01 and neglecting minor losses, calculate the discharge flowing through pipe.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Three parallel pipes connected at the two ends have flow-rates Q₁, Q₂ and Q3 respectively, and the corresponding frictional head losses are hL₁, h₁2 and h13 respectively. The correct expressions for total flow rate (Q) and frictional head loss across the two ends (h₁) are (A) Q = Q₁ + Q₂ + Q3; h₁ h₁1 + hL2 + hL3 (B) Q = Q1 + Q2 + Q3; hL=hL1 = hL2=hL3 (C) Q = Q₁ Q₂ = Q3; h₁ = hL1 + hL2 + hL3 = = (D) Q = Q₁ Q2 Q3; h₁ h1 = hL2 = hL3 = = =
please
Two tanks connected by three pipes in series are shown in Figure 2. The lengths of these pipes are 400 m, 200 m and 250 m and diameters are 300 mm, 200 mm and 250 mm respectively. The difference in water surface in the two tanks is (12+X) m. If coefficient of friction of the three pipes is 0.006, evaluate the following: x=8 (a) Rate of flow through the pipes considering all the losses; (b) Diameter of an equivalent pipe of the same length. H= (12+X) m L;= 400 m L= 200 m Ly= 250 m Jd;= 300 mm d;= 200 mm dy= 250 mm
An oil having a specific gravity of 0.87 is being pumped from a lower reservoir whose water surface elevation is 150 m througha 200mm diameter suction pipe. It is then discharged through a 200 mm diameter pipe to an elevated reservoir whose water surface elevation is 200m The total head loss during the flow from suction to discharge is 12m of oil. Find the volume flow rate of the oil. Select the correct response(s): O0.12 m2/s 0.24 m/s 0.48 m27s 0.36 m/s
Q.8 Venturimeter is installed in a pipe of diameter 40 mm. If the throat diameter of venturimeter is 20 mm and the pressure difference between the pipe and throat section is found to be 120 kPa. Then neglecting the frictional losses, the water velocity in main pipe is (m/s) A В 3 C 4 D 8
A pump is fitted to 100 m pipeline that connects reservoir A reservoir B. The diameter of the pipe is 200 mm and is characterized by a fri factor of 0.02. The design discharge is 0.15 m³/s and the pump. Assuming th minor losses are 20% of friction losses, determine the head the pump must p
0105 Water at 40 °C is pumped from an open tank through 200 m of 50-mm-diameter smooth horizontal pipe as shown in Figure 1 and discharges into the atmosphere with a velocity of 3 m/s. Minor losses are negligible. (a) If the efficiency of the pump is 70%, how much power is being supplied to the pump? (b) What is the NPSHA at the pump inlet? Neglect losses in the short section of pipe connecting the pump to the tank. Assume standard atmospheric pressure. Note: for smooth pipe, friction factor, f = 0.0152 and at 40 °C. kinematic viscosity Temperature (°C) Water vapor pressure (N/m²) Specific weight (N/m³) (m²/s) 6.58 x 10-7 40 7.376 x 10³ 9.731 x 10³ T 3 m ! PUMP 9.731* Diameter = 50 mm Length 200 m e Figure 1
For the flow of fluid at a Reynolds number of 4 x 106 through a 5-cm pipe with a roughness factor of 0.005 mm, what is the Darcy friction factor? O 0.0304 0.0148 0.0124 0.0000160 0.0197 QUESTION 14 You want to insert a valve into a 2.5 inch diameter piping system with a flow rate of 9 ft/min. If you can accept an additional head loss of no more than 2 ft from adding this valve, what is the largest loss coefficient KL you can permit when searching for your valve? O 0.150 6.65 2.03 0.207 1.85
Two tanks A and B are connected by a pipe 30 m long. The first 21 m has a diameter of 75 mm and then is suddenly reduced to 50 mm for the next 9 m. The difference of levels between the tank water levels is 2.40 m. Pipe coefficient f=0.005 and the contraction coefficient at sudden change in area is 0.58. Find all the losses, in terms of velocity v2 at exit from the 50 mm2pipe and hence find rate of flow. Draw the Hydraulic gradient line.
I need help on this question: According to the question: a) If the pipe connected to the pump inlet has a diameter of 24 mm with length (LCP) of 5 m and Darcy friction factor of 0.03, what would be the actual head rise across the pump for a case where the pump outlet pressure is 200 kPa? The difference in height between pump inlet and outlet is 0.25 m, the tank exit is sharp-edged, and the water level in the tank to the tank exit pipe (HWL) is 2 m. Also, consider that the flow velocity inside the tank is negligible. The value of the actual head rise across the pump is = ? b) What would be the pump motor power if the efficiency is 60%? The value of the pump motor power is = ?
Water is pumped through a 750ft long inch nominal diameter sch 40 pipe. The difference in height between the outlet and inlet planes is given as 50 ft. Pump efficiency is 80% and the power of the motor is 20 horsepower. Friction losses are given as 50 ft-lbt / lbm. Calculate the flow rate in the pipeline.
Water at 59 F flows through a straight section of a 6-in-ID cast-iron pipe with an average velocity of 4 fps. The pipe is 120 ft long, and there is an increase in elevation of 2 ft from the inlet of the pipe to its exit. Find the power required to produce this flow rate for the specified conditions. Solve for the fanning friction factor