Q1/Water.p=1.94 slugs/ft and v=0.000011 ft/s, is pumped between two reservoirs at 0.2 ft's through 400 ft of 2-in-diameter pipe and several minor losses coefficient is(12.2m), as shown in Fig. 1. The roughness ratio is c/d = 0.001. Compute the pump horsepower required.

Q1/Water.p=1.94 slugs/ft and v=0.000011 ft/s, is pumped between two reservoirs at 0.2 ft's through 400 ft of 2-in-diameter pipe and several minor losses coefficient is(12.2m), as shown in Fig. 1. The roughness ratio is c/d = 0.001. Compute the pump horsepower required.

Name: Q1/ Water. p=1.94 slugs/ft' and v=0.000011 ft/s, is pumped between tw
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q1/ Water. p=1.94 slugs/ft' and v=0.000011 ft/s, is pumped between two reservoirs at 0.2 ft/s through 400It of 2-in-diameter pipe and several minor losses coefficient is(12.2m), as shown in Fig. 1. The roughnessratio is s/d = 0.001. Compute the pump

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1
19. A centrifugal pump delivering 0 04 cumec of water to a height of 20 metres through a 10 cm diameter pipe 100 metres long. If the overall efficiency of the pump is 75% find the h.p. required to drive the pump. Take f 0'01. (51'83 hp)
An industrial oil (s.g. = =0.85) is flowing at 160 gallons per minute (gpm) in a system with the following details: SUCTION: Standard elbow and the pipe is 7 foot-long. DISCHARGE: Street type elbow and the pipe length is 42 feet. Neglecting losses due to the filter and the hydraulic press, compute: (a) The total energy loss due to friction (suction and discharge pipes) (b) The total energy loss due to minor losses (suction and discharge) 3" Schedule 40 Pump 4" Schedule steel pipe 40 steel pipe Hydraulic Filter press Flow 4.0 ft 早 L0 ft 2.0 ft Reservoir
Q9: Find the specific speed and power consumption for pump having the following properties: (Q=0.1 m3/s), (speed=725 r.p.m) and (head =15 m).
Please help me with this problem, Thank you
A cast iron pipe is to convey oil with specific gravity of 0.9 and a viscosity of 0.00384 Pa-s from one tank to another at a rate of 14 L/s. If the If the diameter of the pipe is 2.75 m, find the Friction factor. Relative roughness is 0.001.
The water is pumped from a 40 sch pipe that has 750 ft lenght, 6 in. nominal diameters. Height difference between exit and entry planes is stated as 50 ft. The yield of waterpump, 80% the power of pump motor is 20 horsepowers. Friction losses are stated as 50ft-lbf/lbm. Please calculate the flow rate in pipe line.
The overall loss coefficient for the pipe shown in Fig.3 is 5; up to A it is 0.8, from A to B it is 1.2, from B to C it is 0.8, from C to D it is 2.2. Estimate the flow rate and the pressures at point C The elevations are shown. el. 12 m el. 10 m Water el. 3 m A B C 8 cm dia. D 3 cm dia. el. 0
need help. Asap
Find the flow rate through the siphon and the pressure at the siphon apex. E.L. 130 m 물 -E.L. 120 m 1=1,500 m d=20 cm f=0.018 FE.L. 100 m Consider reasonable K s c, K s e, Kb values. 1=1,500 m
Calculate the Flow Rate of water at 5°C through the system below. Q = Flow 3.4 m 700 kPa 30 mm diameter DN 65 mm Schedule 40 Pipe
Calculate the NPSHA in ft for the following configuration of a pumping system. Pv=924.8Kpaa ... Vessel Pressure = 134.6 psia Minimum Operable Liquid Level 15 ft Water, 350F Datum Suction Line Losses = 5 ft (1.52m)