It takes 32.53 mL of 0.0205 M permanganate solution to react with 25 mL of unknown oxalate solution. What is the concentration of oxalate in the unknown solution? Report your answer to fo decimal places.

It takes 32.53 mL of 0.0205 M permanganate solution to react with 25 mL of unknown oxalate solution. What is the concentration of oxalate in the unknown solution? Report your answer to fo decimal places.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter4: Types Of Chemical Reactions And Solution Stoichiometry

Section: Chapter Questions

Problem 47E

See similar textbooks

Similar questions

Calcium carbonate, CaCO3, can be obtained in a very pure state. Standard solutions of calcium ion are usually prepared by dissolving calcium carbonate in acid. What mass of CaCO3 should be taken to prepare 500. mL of 0.0200 M calcium ion solution?
Twenty-five milliliters of a solution (d=1.107g/mL)containing 15.25% by mass of sulfuric acid is added to 50.0 mL of 2.45 M barium chloride. (a) What is the expected precipitate? (b) How many grams of precipitate are obtained? (c) What is the chloride concentration after precipitation is complete?
What happens if you add a very small amount of solid salt (NaCl) to each beaker described below? Include a statement comparing the amount of solid eventually found in the beaker with the amount you added: a a beaker containing saturated NaCl solution, b a beaker with unsaturated NaCl solution, c a beaker containing supersaturated NaCl solution. A saturated sodium chloride solution.
. Why does the amount of excess solid solute present in a solution not affect the amount of solute that ultimately dissolves in a given amount of solvent?
A patient has a “cholesterol count” of 214. Like manyblood-chemistry measurements,this result is measured inunits of milligrams per deciliter (mgdL1). Determine the molar concentration of cholesterol inthis patient’s blood, taking the molar mass of cholesterolto be 386.64gmol1. Estimate the molality of cholesterol in the patient’sblood. If 214 is a typical cholesterol reading among men inthe United States, determine the volume of such bloodrequired to furnish 8.10 g of cholesterol.
The iron content of hemoglobin is determined by destroying the hemoglobin molecule and producing small water-soluble ions and molecules. The iron in the aqueous solution is reduced to iron(II) ion and then titrated against potassium permanganate. In the titration, iron(ll) is oxidized to iron(III) and permanganate is reduced to manganese(II) ion. A 5.00-g sample of hemoglobin requires 32.3 mL of a 0.002100 M solution of potassium permanganate. The reaction with permanganate ion is MnO4(aq)+8H+(aq)+5Fe2+(aq)Mn2+(aq)+5Fe3+(aq)+4H2O What is the mass percent of iron in hemoglobin?
95. Many metal ions form insoluble sulfide compounds when a solution of the metal ion is treated with hydrogen sulfide gas. For example, nickel(II) precipitates nearly quantitatively as NiS when H2S gas is bubbled through a nickel ion solution. How many milliliters of gaseous H2S at STP are needed to precipitate all (he nickel ion present in 10. mL of 0.050 M NiCl2 solution?
Fluoridation of city water supplies has been practiced in the United States for several decades. It is done by continuously adding sodium fluoride to water as it comes from a reservoir. Assume you live in a medium-sized city of 150,000 people and that 660 L (170 gal) of water is used per person per day. What mass of sodium fluoride (in kilograms) must be added to the water supply each year (365 days) to have the required fluoride concentration of 1 ppm (part per million)that is, 1 kilogram of fluoride per 1 million kilograms of water? (Sodium fluoride is 45.0% fluoride, and water has a density of 1.00 g/cm3.)
Addition of water to concentrated sulfuric acid is dangerous because it generates enough heat to boil the water, causing it to spatter out of the container. For this reason, chemists remember to add acid to water. In a dilution experiment, we calculate the amount of the more concentrated solution that must be measured out. If we place this concentrated solution (Figure 4.7) in the volumetric flask first, then dilute with water, we violate the caution Add acid to water. Describe a safer variation on the method shown in Figure 4.7 that allows the quantitative dilution of concentrated sulfuric acid. Figure 4.7 Preparing a dilute solution from a concentrated solution. (a) Draw the concentrated solution into a pipet to a level just above the calibration mark. (b) Allow the liquid to settle down to the calibration line. Touch the tip of the pipet to the side of the container to remove any extra liquid. (c) Transfer this solution to a volumetric flask. Again touch the pipet to the wall of the flask to ensure complete transfer, but do not blow out the pipet because it is calibrated for a small amount of liquid to remain in the tip. (d) Dilute to the mark with solvent. Frequently, especially with concentrated acids, it is best to have some solvent present in the volumetric flask before you add the concentrated sample.
Relative solubilities of salts in liquid ammonia can differsignificantly from those in water. Thus, silver bromide issoluble in ammonia, but barium bromide is not (thereverse of the situation in water). Write a balanced equation for the reaction of anammonia solution of barium nitrate with an ammoniasolution of silver bromide. Silver nitrate is soluble inliquid ammonia. What volume of a 0.50 M solution of silver bromidewill react completely with 0.215 L of a 0.076 M solutionof barium nitrate in ammonia? What mass of barium bromide will precipitate fromthe reaction in part (b)?