It is known that V. = 45 mV loss = 12 mA, Vp = -4 V, VGSQ = -2.5 V, RD = 4.2 k and Rs = 1.2 k in the circuit in the figure. Accordingly, the value of the output voltage of the circuit What is (vo)? NOTE: FET output impedance (ra) will not be taken into account in calculations. V₁ Z a. 637.88mV b. 297.68mV Oc. 85.05mV O D. 552.83 mV Rs Oto. 765.45mV O f. 425,25 mV O g. 893,03 mV Oh. 170,10 mV mi NIT RD Zo DD

It is known that V. = 45 mV loss = 12 mA, Vp = -4 V, VGSQ = -2.5 V, RD = 4.2 k and Rs = 1.2 k in the circuit in the figure. Accordingly, the value of the output voltage of the circuit What is (vo)? NOTE: FET output impedance (ra) will not be taken into account in calculations. V₁ Z a. 637.88mV b. 297.68mV Oc. 85.05mV O D. 552.83 mV Rs Oto. 765.45mV O f. 425,25 mV O g. 893,03 mV Oh. 170,10 mV mi NIT RD Zo DD

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

DC DC Converters a) A step-up PWM converter has the following data: V = 8 V, Vo = 24 V, lo = 1.25 A, and f = 200 kHz. Calculate the minimum inductance required for the converter operation in CCM (Continuous Current Mode). Then, determine the required capacitance for the converter. Assume n = 100 %. b) Design a boost SMPS converter to meet the following specifications: V = 80 V, Vo= 400 V, R. = 480 n, f.= 25 kHz, VNOS 1%. Find L, C, minimum inductor current lupin), maximum inductor current tunan), and output power. Then, sketch the inductor voitage and current waveforms for one cycle.
Find the numerical value for R. for maximum power transfer for Ro. Find Pmax- 5 0 4 0 0.85 vA Ro 24 V 6 is +)
6
A step up DC converter is used to control power flow from a DC votage Vs=120V to a battery voltage E=200V. The power transferred to the battery is 10 kW. The current ripple of the inductor is negligible. The duty cycle and the effective load resistance as seen from the input are respectively equal to: Select one: Oa. 0.5, 0.94 Ohms b. 0.4, 1.44 Ohms Oc. None of these O d. 04, 0.94 Ohms
The second photo is a solution from bartleby expert but they never gave any plot sketches! Can you help me plot the graphs?
Answer in Handwriting only
The circuit shown in Figure having resistor 150 Q and a capacitor 30 µF is connected to a 210 V, 60 Hz supply. Determine: (i) Impedance of the circuit (ii) the voltage across the resistor (ii) the voltage across the capacitor (iv) the power factor ww -VRT -Vc– I V
In a 220 Vrms, 60 Hz. Source, determine the following values:
Consider the following circuit used to provide power for an inductive RL load. The input voltage is Vs=150V and the load has a 30 impedance value. The thyristor is working at a frequency fs = 2 kHz. The discharge current is to be limited to 50A and the required dv/dt is 50V/us. The values of Rs and Cs are equal to: Cs Ti V, Select one: O a. 30, 0.158µF b. 30, 0.352µF ос. 30, 0.64µF O d. 60, 0.5µF
In the circuit given in the figure VT = 25mV, | VBE | = 0.7V, R1 = 515.22Kohm, R2 = 10.89Kohm, R3 = 2.41Kohm, R4 = 1.03Kohm, VCC = 12.00V, VEE = 2.00V, VA = 12.51V, Beta Since = 107.00, Rs = 23.19ohm, Ry = 8.18Kohm, calculate the IC current, Ri, R0 and voltage gain according to the Source (V0 / V1) by making full analysis.
Consider the following step up converter with a resistive load of value RS ohms. it is supplied by a DC power source of magnitude Vs-200 V. The switching frequency is5 kHz and the duty cycle k is first set to 05 and the inductance used within the circuit has a value of L-10 mH. The switch is supposed to be ideal. if the average supply current is BOA then the average load current is: Select one: O a. la 80A O b. la 40A O cla 50 A O d. la 81 A
A buck converter is designed to achieve ripple in the voltage (?Vo/Vo<0.38%), given that: fs=20KHZ, Vin= 100V, Vo=0.25*Vin, Ro=100 Ohm, What is the capacitance value that is used in this design? O a. 2.63*10^(-5) F. O b. 1.33 10^(-5) F. Oc 3.33*10^(-5) F. O d. 1.22*10^(-5) F.