Isometric View: 30.5in (from left edge of load to right edge of load) K 1.5in 6.5in 1.5in 6.5in 1.5in 6.5in 1.5in 6.5in 1.5in Top View: 15lbs 15lbs 15lbs 15lbs 33.5in (length of rod) 30.5in (from left edge of load to right edge of load) 1.5in 6.5in 1.5in 6.5in 1.5in 6.5in 1.5in 6.5in 1.5in 15 lbs Cross-section View: 15 lbs 15 lbs 12in diameter 33.5in (length of rod) 15 lbs 15 lbs 4 cylindrical masses that weigh 15 lbs each are being supported by 2 solid stainless steel rods. The two rods are secured at both ends, the rest of the rod is suspended. Determine the minimum rod diameter that the 2 rods must have to support the loads without bending.

Q: If I had one singular hinge joint, which total different direction could it provide a force in?

A: The hinge joint can rotate and proves zero restriction about the hinge point, thus moment reaction…

Q: -:) To replace the regular light bulb with a high-efficiency light bulb, what is the upper price…

A: Unit cost of electricity, Type of light bulbCost ($/piece)Power (W)Lifetime (hours)Regular…

Q: how much vertical and horizontal force the upper arm is exerted on the forearm?

A:

Q: What are forces on pin C and D

A:

Q: Select the reaction forces in a roller support. Horizontal Reaction Moment Reaction Vertical…

A:

Q: The bearing arrangement depicted below is often used for car wheel hubs because: 11

A: Given:Diagram and questionTo determine:to choose correct option for the given question

Q: Truss members can change their length due to a change in temperature. True or false?

A: In truss members, there is no change in length. But due to changes in temperature stress is build up…

Q: Due to imperfections in manufacturing or specific applicationof the load, a column will never…

A: Under the application of axial load over a column when there is a deflection in the lateral…

Q: . A self-locking C-clamp is used to hold a workpiece with a clamping force of 5000 lb. The screw has…

A: Draw FBD

Q: What type of external forces or load should be applied in truss system and which part at the truss…

A: A truss is defined as a structure that is composed of various links or slender members which are…

Q: Draw the Mohr Circle and mark important points for a rod under pure tensile load & torsion

A:

Q: What is the magnitude of the Right Reaction force in pounds?

A: GIVEN: F=1.5 kpis =1500 lbf TO FIND: The reaction on the right side. Rb

Q: If I have a singular roller joint, in which total different directions can it provide a force in?

A: A roller joint typically refers to a joint or connection that allows rotation about a single axis.…

Q: To decrease the amount of force needed increase the of the inclined plane. distance or length O…

A: Given Data⇒ Inclined plane

Q: A shape factor that measures a column’s resistance to buckling about an axis. -radius of gyration

A: The radius of Gyration gives the relationship between the cross-section area of the column and the…

Q: For nos. 24-37, satisfy the conditions of the g below: The truss is loaded as shown in figure of…

A: Ans: 25. Option D is correct. 11.2 kN compression

Q: Two gas struts with a extended length of 26", compressed length of 16" and a stroke of 10" with a…

A:

Q: y 250 lb/in 100 lb/in X 7.5 ft - 5 ft –

A: The load distribution according to the composite area method is as follows: First, divide the into…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.