is considered an application of nanomaterials in biomedical * O drag transform scanning coating O not of them by comparison between Carmat Artificial Heart and Syncardia Total Artificial Heart, select the correct options * Carmat generates audible noise Syncardia Artificial Heart needs to external pneumatic actuator Carmat not generate audible noise Carmat Artificial Heart needs to external pneumatic actuator

Q: Determine the Resultanto f the eoplanar orcesestem

A:

Q: what is 6 to 10 po?

A:

Q: where did 144 come from

A:

Q: solution incorrect resolve again

A:

Q: resolve solution

A:

Q: What about the 100N weight?

A: There is a thin triangular plate in x-y plane.And location for the center of gravity is to be find…

Q: salve gine a- when

A: givendifferential equation xdydx+cosy=0y=π4  when x=2

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: Figure 3 shows one cart with a mass that is separated from two walls by two springs and a dashpot,…

A:

Q: (b) Compute the internal torque exerted on gear A (TAC), gear C(TcD) and gear D (TDB). (c) Sketch…

A:

Q: 10 kNim 50 kN Identify the moment diagram of the beam shown. 3125 3125 (AN mA 022 (AN-m)A

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: can you answer 1B

A:

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: Q1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket…

A:

Q: You are designing a new engine; this device operates with liquid fuel as an input and gener energy…

A: Hello. Since you have posted multiple questions we will solve the first question for you. If you…

Q: □ 18 F.V.

A: According to the details provided in the question, we need to draw three projection views.

Q: What is the length and wall thickness of the vertical bear

A: For figure 2,  drawing and the type of symbols present

Q: As shown, a section of a roller coaster track (Eigure 3) follows the form of y = (2/3)x¹.5 Locate…

A:

Q: Using the method of joints, determine the force in each member of the truss shown. State whether…

A:

Q: Given : Mass of Gears A and B = 2.4 kgs Mass of Gear C = 12 kgs Gears A and B's radius of gyration =…

A:

Q: ********** QI/A/ The 4-mm diameter cable BC shown in Figure Q1-4 is made of a steel with E-200 GPa…

A:

Q: A multi-stage pump, 260 gpm capacity is installed in a well 27 ft below the static water level.…

A: Given data:  The capacity of the pump is given as Q = 260 gpm = 0.579 ft3/sThe total discharge head…

Q: Incorrect please resolve both parta

A: To calculate the surface temperature of the tank when it is passed through water and to calculate…

Q: Calculate the number of degrees of freedom The value must be a number 11 Calculate the number of…

A: Full joint is the joint which has area or surface contact, and half joint is the joint which has…

Q: (12m) ladder weighs 200N and is ed against a smooth vertical wall its lower and (6m) from the wall

A:

Q: Figure 1 of 1 30 40 F2

A: Given, F1 = 210 N F2 = 510 N Angle between two forces = θ = 40°

Q: At a given moment four link mechanism OABO, is in the position shown on the figure and OA= AB = AO =…

A:

Q: (d) Water flows in two different horizontal pipes having a height difference of 55cm. A U- tube…

A:

Q: How do you know that it is -1.2? What determines the sign?

A: Given: How do you know that it is -1.2? What determines the sign?

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.