Interior pin | 20KN 20kN/m 3m

Q: 1. Which of the following gives the moment at the built-in of the continuous beam? a. -5825 N.m…

A:

Q: The cantilever beam carries a triangular load, the intensity of which varies from zero at the left…

A:

Q: STRUCTURAL THEORY Show complete solution for better understanding In the frame shown in figure below…

A: EI = ConstantE = 200 GPaI = 1200 × 106 mm4 Determinea. The reaction at D. b. Moment reaction at AB.…

Q: What is the vertical reaction at A for the frame shown? 2 k/ft B 100 k •ft 15 ft El = constant E =…

A: Figure is as shown

Q: The cantilever beam carries a triangular load, the intensity of which varies from zero at the left…

A:

Q: An overhang beam is situated above a cantilever beam carrying its roller support. Determine the…

A:

Q: What is the maximum value of moment at A in KN-m?

A: To find moment at A

Q: solve for the remaining reactions and also put the directions

A:

Q: The influence line for the reaction at B for the beam shown changes curvature between A and B;…

A: Given that there is curvature change between points A and B.

Q: 1. A frame shown is subjected to the given loading. Without considering sidesway and using moment…

A: Fixed end moments for beam AC and CD can be determined by using principle of superposition.

Q: SITUATION. The beam shown is subjected to a uniform dead load of 1.2 kN/m, a concentrated dead load…

A:

Q: What is the vertical reaction at A for the frame shown? 2 k/ft 100 k ft 15 ft El = constant E =…

A: Given:- EI=Constant E = 29000 ksi I = 3500 in4 To find:- Reaction at A

Q: Determine the magnitude of the moment of P about the y-axis in Nm

A: Given that: P = 14i-16j

Q: a) Determine moment at point B. b) Calculate for the maximum moment and its location from A. ) Draw…

A:

Q: Determine the reactions at point A, B, C, D and get the Shear and Moment diagram

A: Given, is a structural analysis problem.   In order to determine the support reactions, we will need…

Q: The reaction at support B RBy IL. The reaction at support C RAy III. The bending moment a

A:

Q: What is the maximum value of moment at D in KN-m?

A: We will apply the concept that moment at hinge is zero if no external moment is applied.

Q: The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by…

A:

Q: Construct the influence lines for the support reactions, and then use them to obtain the influence…

A: Let load(P) applied be unit load i.e, P = 1 unit

Q: SET 4: 100 kN w = 40kN/m TIM. C 5m Зт р 3m A 8m OB 10т THREE MOMENT EQUATION METHOD 11) What is the…

A:

Q: 2m

A: Sign convention used for ILD:Influence line for reaction is positive if the reaction acts upwards.…

Q: For the beam shown, calculate the reactions. Calculate the moment at point C. Also, calculate the…

A: We need to find out reactions, moment at C and shear at C

Q: SITUATION VI: A frame is loaded as shown in the figure. |16 kN 1 m В 5 m A D 5 m 14. What is the…

A:

Q: Neglecting the mass of the beam, compute the reactions at A and B.

A: Solution: According to the diagram: ∑Fx=0  terefore, HB=0 ∑Fy=0 RA+RB+2-12×1×6=0 RA+RB+2-3=0RA+RB=1…

Q: Determine the reaction at support B for the simple beam shown.

A: W1=323=96ky1A=distance from A=3+32=4.5ftW2=12323=48ky2A=distance from B=2×33=2ft

Q: The beam is shown  a.) What is the reaction at A in KN? b.) What is the vertical reaction at B in…

A:

Q: Determine the resultant couple moment acting on the beam.

A: From the given figure, we can calculate the moment from both sides (either from right side or from…

Q: the beam shown, determine the maximum negative ent. In kN.m 19 kN 3 kN/m |B 2 m 2 m 2 m

A:

Q: For the frame shown, determine the magmtude of the pin reaction at B. neglect the weight of the…

A:

Q: The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by…

A:

Q: Draw the influence line for vertical reaction at support A. A В C D -1.6 m -1.6 m -1 m-

A:

Q: Problem 2. Determine the hinge reactions (in kN) at point B on the beam shown. 20 KN 20 KN 20 KN 20…

A:

Q: 50 kN/m 20 kN/m IMANTIHalinomm Kam * A D B 4 m 3 m 4 m RA Rp

A:

Q: 55 kN 64 kN 100. kN/m D B Im 3m * Im R1 FIGURE A R2

A:

Q: 50 KN 60 KN/m 20 KN/m 20 KN/m G E 20 KN/m 20 KN/m 20 KN/m 0.50 2.00 2.50 | 1.00 4.00 All dimensions…

A:

Q: 20 kN/m 3 m B 30 KN C 1m 1m D Section of the beam: 300 mm 400 mm 20 kN/m 3 m 450 mm E

A: As per policy we are only supposed to answer first three sub parts

Q: solve for the reactions of the beams

A:

Q: | 5.14 Assuming that the reaction of the ground is uniformly dis- tributed, draw the shear and…

A: A beam with load arrangement is given as shown in the figure above and it has been asked to…

Q: load of 5 KN/m on the 3 m portion of the beam from the free end and a counterclockwise couple of 60…

A:

Q: The cantilever beam carries a triangular load, the intensity of which varies from zero at the left…

A:

Q: Solve for: A) Reactions at Point A and B B) Location of Positive Maximum Moment (x) C) Value of…

A:

Q: Draw the shear force and bending moment diagram for the beam

A: The following figure shows the Free Body Diagram of the beam.

Q: Determine all the reactions on the following beam. Use AREA MOMENT METHOD. 75 kN/m 50 kN/m A. 3m 2m…

A:

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.