1. Which of the following gives the moment at the built-in of the continuous beam? a. -5825 N.m b. -5258 N.m c. -5528 N.m d. -4693 N.m 2. Which of the following gives the reaction at the built-in of the continuous beam? a. 3077.4 N b. 7307.4 N c. 3707.4 N d. 3770.4 N

Q: What is the value of the reaction at the right support in kN?

A:

Q: Provide complete solution: Check the determinacy of the beams and solve for the reactions at the…

A: determinancy of the beam is 1calculation of fixed end…

Q: What is the maximum value of moment at A in KN-m?

A: To find moment at A

Q: Calculate the reactions of the beam using Moment Distribution Method P = 29 k, W = 2.4 k/ft, a =…

A: Concept We will use method of moment distribution to get the final moment at supports then by…

Q: Solve for the reactions and draw the shear and moment diagram. (7) MN kN-m 4m 6 m

A:

Q: An AB beam of 1350 N contain a load of 2250 N in B. The beam is maintained by fixed support in A and…

A:

Q: The influence line for the reaction at B for the beam shown changes curvature between A and B;…

A: Given that there is curvature change between points A and B.

Q: 4 Which of the following gives the reaction at D in the given beam? 300N₁ 210 N/mp 100 Nm TIT777 5m…

A:

Q: The beam is used to support a dead load of 2 k/ft, a live load of 2 k/ft, and a concentrated live…

A: since the given question has multi-parts therefore as per guidelines only 1-3 part will be solved.…

Q: Determine the reactions of the beam. 270kN 67.5kN-m 60 3m 1.2m 2.1m

A:

Q: Determine the horizontal component of reaction and the vertical component of reaction at D. Also…

A: Given : P1 = 9 kN and P2 = 17 kN Determine the horizontal and vertical component of reaction at D ?

Q: Which of the following gives the reaction at E in the given beam??

A: We know that at internal hinge we get zero bending Moment. And reactions at hinge will get…

Q: 4 kips/ft Α D Bodo 000 25 ft 25 ft 25 ft

A: The length of the span AB(LAB)=25 ft, The length of the span BC(LBC)=25 ft, The length of the span…

Q: QUESTION 6 The compound beam shown has internal pin at point B. 150 lb 200 lb/ft 5/4 85 lb/ft 120…

A:

Q: 11.6 kips Part 1 2.9 Correct 2.2 3.9 kips 5.1' OB RA If the resultant passes through B, the original…

A:

Q: find all reaction for the frame by the force method

A: Let's take Hc as redundant  Using Theorem of least work (Force Method)

Q: 2. Solve For the reactions at and

A: The equilibrium conditions can be applied to a beam with 2 unknown reactions. The values like the…

Q: Iculate the reactions at B using Portal method if P = 30KN. P. E 6 m B E 6 m -9 m to - 6 m

A: portal method of frame analysis is a approximate method of analysis based on assumption that are :-…

Q: From the given beam: Calculate the reaction at point B. If the concentrated force is equal to 40…

A:

Q: For the beam shown, calculate the reactions. Calculate the moment at point C. Also, calculate the…

A: Given data in question  Simply supported beam  UDL Point load To find out Reactions  Moment at C…

Q: Determine the components of the reactions at E if a 750-N force directed vertically downward is…

A: Figure is as shown

Q: Determine the following: a. vertical reaction of the support A in kN b. horizontal reaction of the…

A:

Q: 3. Construct and draw influence lines for the reactions at A, C and E, the shear at D, the moment at…

A:

Q: Determine the reactions in the following beam with El constant and solve them using the stiffness…

A:

Q: vertical reaction at B, and (d) the moment at C. Assume the support at A is a pin and B is a roller.…

A:

Q: solve for the reactions and also put the directions

A:

Q: B3- Determine the reactions and draw the shear and bending moment diagrams for the following beam…

A:

Q: Calculate the reaction on the beam if W1= 13 kN/m P 10 kN M = 17 kN-m Counter clockwise x-6m y=2m…

A:

Q: Using Superposition method, determine the reachon at each support of the beam. 15KN/m 6 kn/m

A:

Q: 100KN 10 kN/m B Com 21 12m E= constant EL LL

A:

Q: The beam is used to support a dead load of C kN/m, a live load of A kN/m and a concentrated live…

A:

Q: PROBLEM 2 For the beam shown, determine the reactions at A, B and D. At B, C and D is a pin and at A…

A: Given data  Find reactions at A, B and D.

Q: 30KN/m sokwlm Zim 3m im 4m

A: Given data in question  Simply supported beam  UVL UDL Span member length  To find out  Reactions…

Q: 520 N/m 230 N/m Chinged 15m 6m BO 13m N

A:

Q: A key is used to turn an axle. A pin fits into hole A and a flat, frictionless surface rests at…

A:

Q: The truck has a mass of 4 Mg and mass center at G1, and the trailer has a mass of 1 Mg and mass…

A: To get maximum bending moment heavy load must be placed such that heavy load and the resultant of…

Q: Determine the reactions of the following beam of constant EI.

A:

Q: The frame shown is supported by a hinge at A and a rocker at D. The frame is acted by the force…

A: The value of the UVL actin over span AB = 12×300×5 = 750 N or .75 KNIt will act at 53m distance from…

Q: Determine the reactions in the following beam with El constant and solve them using the stiffness…

A:

Q: Determine the components of reaction at the fixed support A. Neglect the thickness of the beam.

A: Determine the components of reaction at the fixed support A. Neglect the thickness of the beam.

Q: of 3x+ 2000lb aft FR₂

A:

Q: 3. Loaded as shown, the beam rest in the incined smooth surface at A and supported by a hinge at B.…

A: To Find :- Support reactions at A & B.

Graphical Methods

The graphical method is a method of solving equations involving more than one variable using the Cartesian coordinate system. In civil engineering, the use of the graphical method is limited to the problems involving two variables. The graphical method has a great impact in solving the questions regarding engineering mechanics.