A key is used to turn an axle. A pin fits into hole A and a flat, frictionless surface rests at point B on the shaft. If a force P of magnitude 250N is applied to point D of the switch, determine : (a) the reaction at B (b) the component of the reaction at A in the direction perpendicular to AC. 75 mm 375 mm

A key is used to turn an axle. A pin fits into hole A and a flat, frictionless surface rests at point B on the shaft. If a force P of magnitude 250N is applied to point D of the switch, determine : (a) the reaction at B (b) the component of the reaction at A in the direction perpendicular to AC. 75 mm 375 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solid.mech.torsion
The solid shaft that is fixed connected at both ends has a diameter of 20 mm and a total length of 2m. If it is subjected to two torques 500 N.m clockwise, positioned 0.3 m from the support A and 800 N.m counterclockwise positioned 0.2 m from the support D. Determine the reactions at fixed supports A and D. Express your final answers in N.m.
Determine the Horizontal Reaction at B
The shaft is connected to a generator at A and the torque applied at each of the four gears is as follows: Tu = 40 N.m. T. = 25 N.m. T, 34.5 N.m. T, 23 Nm. The shaft is made of Aluminum 2014-T6 and H has a polar moment of inertia J= 2 *10 m. Find the angle of twist of gear E with respect to gear D knowing that the distance between the two gears is 840 mm. O0.0537 rad O0.0358 rad 10.0132 rad O 0.933 rad 40.0179 rad
The frame shown is supported by a roller at A and a pin at B. Determine the components of reaction at A, B, and C. 28 K 4 ft 8ft 2.0 2.0 45° 45 16.0 ft
If the mass of cylinder is 100 kg, find the tension developed in wires AB and AC and find the support reactions in point O.. X 3 m 1.5 m 1.5 m 3 m. B 1 m
Statics of Rigid Bodies (Round off to two (2) decimal places. Include negative sign (-) if the answer is negative.) A prybar is used to remove a nail as shown. Determine the moment of the 240 N force about the point O of the contact between the prybar and the small support block. (in N-m)
SUBJECT:Structural Theory Kindly give the accurate solution and the answer. Thank You
7m 2KN 3m 2KN 20KN 1-calculate the reactions 2- plot the normal (N) force diagram 3- plot the shear for digram 4- plot the moment 5- calculate the deflection and plot it
L+I ab)" a~bm 1 - 2- 6 STATICS ENGINEERS MECHANICS CHAPTER Lecture Notes: = m Σ τ a Z=Dy+3 EXAMPLE: 22 December The flywheel A rotates clockwise under the action of a 700 N-m couple. A band break is to be used to stop the rotation of A. The coefficient of friction between the belt and the flywheel is 0.40. a.) What is the minimum force applied at the end of rod B that will stop the flywheel? 2 = y +3 b.) If the 700 N-m couple acts counterclockwise on A, what is the minimum braking force P? P2 1 1+X CO 700 N.m P 6÷3 B 0.6 m 1.2 m ?+2 =4 180- mennin g is goeed Sa