A oud Spyiay Go 20 s Oher s JM of s fapon Apyhs s 50 mg a .TEQ”‘ he Spnngs prne of dhe gosie ——height aund bave o coils each. With e ek by 50 mm- _In & Inside a helical sping of cioculal crolsin diameter. anotheris placed having thesection 2o mm.springCross- section. theSameofradieswhere asthat of the Pnner spmng is 50 ms-meanthe outer spring is80 MMis 50 m MaBoth the Spningsheight and havea load being trans nitte dthey defectaree of the same10 coilseach. Witthatoboth theby 50 mm-is the maxinuM shealstoes gseater, dnd what are theirInspringswhich springMaguitides?what is the coreponding1oad being transmitted ? The shear6ath theModulusCE80G PaApring puterials.

Helical springs are formed of wire that is coiled into a helix shape and is designed to handle…

Inside a helical spnng of cistulal crols section 20o mm. spring Cross- section, the the outer Spning that of the Both the Spnings height and have a load being trans nitte d Springs they defect by 50 mm- which spring stoes gseater, dnd what are their Maguitides? 1oad being transmitted ? The shear Modulus in dianeter. another is placed having the Same radius of where as mean is 80 MM Inner spng is 50 mma are of the same each. With to both the 10 coils In is the maxinum sheal what is corepondi. C=80GPA for Gath lhe Apxing Materiale.

Inside a helical spnng of cistulal crols section 20o mm. spring Cross- section, the the outer Spning that of the Both the Spnings height and have a load being trans nitte d Springs they defect by 50 mm- which spring stoes gseater, dnd what are their Maguitides? 1oad being transmitted ? The shear Modulus in dianeter. another is placed having the Same radius of where as mean is 80 MM Inner spng is 50 mma are of the same each. With to both the 10 coils In is the maxinum sheal what is corepondi. C=80GPA for Gath lhe Apxing Materiale.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The truee ia loaded se anown. 60 kN 120 kN 120 kN 120 kN 3m 3m. 6m 3m Cnocee the magnituce (kN) and type (tenaion or oompreaeion) of the foroe in member GF. NOTE: Alwaya ohooae two (2) anawera but if the member ie a zero-foroe member ohocee one (1) anawer only. Seleot the corect reoponoe(o): 7211 Teneion 60 180 260 36.06 | 100 63.25 Compression 50 160 O O O
11 Design the rod. (Find the diameter d). (2 Puan) F = 60KN, Gall = 120MPA y C A В F L d = 25.2mm d = 20.1mm d = 19.5mm d = 22mm d = 28.2mm d = 24.8mm
with ne glibhe is pioneal at 0 amel wh mek. le ad P can be affuched to two verticle yods applied withect esuc dig sfars ofiso Mfa in steel rod, and 7. Mla in b ronze rod. 1. Sm 1.Sm steel Branse A- 300 m2 E= 23 Gr, L= 2m
i need the answer quickly
Don't try if u don't know.
2. A transmission shaft of 70mm diameter is subjected to the torques shown. Knowing that [t ]=60Mpa. O draw the torque diagram. Ocheck the strength of the shaft. ( 20Scores) 700N.m 900N.m 1600N.m A
#21. a puhip fropeller Ahaft haw a diameter off 0.35 meters. the allowabre wrlking and the allowable angle on twist u 1 deqe acrosi ita, lengthe equal to 15 diameters stress in Ahear ia 50 megaPaseals %3D brwe fow maximum torque the thaft can transmit
Q1 The power of motor is (15)H.P rotating to (1800) rpm design the key which to located on the shaft motor if the diameter of it is (60) mm and shearing and crushing stresses which applied of it are 40N/m? and 70N/m2 respectively
down by iS 12 mm wide EsSembled 4 A duralumn Calinder head is held deun by Steel bolt each 65 mm whieh fung. Just eind belt is tightened thread Compressed inside when eech made tight end ie then turn (e eg linder head a tube 12 eudside by. Fur Her Luarler ef l-5 mm). The Considered Piteh Cen be diameter diemeter. Determine the stresses in Hhe eund 25 mm Steel eind dusalumin. Take E = Luo Ida Steel %3D Cnd 684N/mm". dur
I need answer within 20 minutes please please with my best wishes
Treactuon Prob2 750N)m B 90DN-m The compound shaft 1200N-m C has a uniform Cross sechonal area with the ginen le ngth op each segment. 3 Diff diameter Usng the applied torque on the indicate porition ,det. the safe dia of the shaft f the allow stress m each from Anqular seg ment u shown + 3,4m 2.3m 15m Hint : Allow Torsional Segment Stress G from stress analy sis 70 GAa AB GOMPA, 89GPA BC 28GPA CD 75MPA' 50 MPa t one Ans of di ameter defomato. the free end angular de formatun u limited to 2,8°
None