Initiator lj häs hålf the izes 4 times as fast as monomer M2 at 80°C, when initiator I is used for both and all the concentrations are the same. What is the ratio of degree of polymerization for M1 and M2 if they are polymerized with initiator I1 and I2, respectively, the ratio of monomer concentrations being 1:2 and that of initiator concentrations being 1:5? It can be assumed that both polymers terminate exclusively by coupling and that the initiator efficiencies are equal.

Initiator lj häs hålf the izes 4 times as fast as monomer M2 at 80°C, when initiator I is used for both and all the concentrations are the same. What is the ratio of degree of polymerization for M1 and M2 if they are polymerized with initiator I1 and I2, respectively, the ratio of monomer concentrations being 1:2 and that of initiator concentrations being 1:5? It can be assumed that both polymers terminate exclusively by coupling and that the initiator efficiencies are equal.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Where is the intermediate formation theory of catalysiis used ?
I need a solution within 15 minutes
Iodine is sparingly soluble in water but much more so in carbon tetrachloride. The equilibrium constant, also called the partition coefficient, for the distribution of I2 between these two phases I2(aq) =12(CCI4) is 83 at 20°C. (a) A student adds 0.028 L of CCI4 to 0.213 L of an aqueous solution containing 0.037 g I2. The mixture is shaken and the two phases are then allowed to separate. Calculate the fraction of I2 remaining in the aqueous phase. 4.0 (b) The student now repeats the extraction of I2 with another 0.028 L of CCI4. Calculate the fraction of I2 from the original solution that remains in the aqueous phase. 4.0 (c) Compare the result in (b) with a single extraction using 0.056 L of CCI4. Comment on the difference. After a single extraction using 0.056 L of CCI4, the fraction of I2 that remains in the aqueous phase is 40 This result is larger than the result in (b), which means that a single large extraction is not as efficient as two separate smaller extractions.
Construct the expression for Ksp for solid Ba3(PO4)2 in aqueous solution. Вa (РО:)-(s) 3D З Ва" (аq) + 2 РО.* (аq) 1 Based on your knowledge of how the solid will dissociate in aqueous solution, use the tiles to form the expression. Ksp 5 RESET [Ba-(PO:)] 2[Ba:(PO:)-] 3[Ba:(PO:)-] [Ba-(PO:).J? [Ba:(PO:):]3 [Ba*] 3[Ba*] [Ba*j [Ba*"] 3[Ba"] [PO.2] 2[PO] [PO.P [PO.] 2[PO.] [PO. P 3[PO.] [PO. P
Solve all parts otherwise I will downvote
In a study of the decomposition of ammonia on a platinum surface at 856 °C NH3¬1/2 N2 + 3/2 H, the following data were obtained: NH3), M 1.95x10-3 1.50x103 9.75x10-4 1.75x103 7.80×10-3 3.90x10-3 seconds 0 1000 Hint: It is not necessary to graph these data. (1) The observed half life for this reaction when the starting concentration is 7.80×103M is s and when the starting concentration is 3.90×103 Mis (2) The average rate of disappearance of NH3 from t= 0 s to t= 1000 s is ]Ms!. (3) The average rate of disappearance of NH3 from t= 1000 s to t= 1.50×103 s is ]Ms!. (4) Based on these data, the rate constant for this v order reaction is Ms!
I just want someone to evaluate if my answer is correct or if it's wrong do the correct way to me. I've been asking this question here about Langmuir isotherms and got no response. So please evaluate is this is correct or wrong. Thank you in advance.
I need help rewriting this without copying word by word. Could you help me? Could you also use different references from different sources?
To study the photochemical decomposition of aqueous bromine exposed to bright sunlight, we dissolved a small amount of liquid bromine in water contained in a glass jar and placed under direct sunlight. The following data were obtained at 25\deg C:\table [[Tiempo (min ), 10, 20, 30, 40, 50, 60], [Ppm, 2.45, 1.74, 1.23, 0.88, 0.62, 0.44]] Determine the reaction rate order and the specific reaction rate constant: a) Differential method ( The method for obtaining the derivatives is left to your decision) Tiempo (min) Ppm Br₂ 10 2.45 20 1.74 Ć 30 1.23 40 0.88 50 0.62 60 0.44
19. The lattice diffusion coefficient for Al ions in Al₂O₁ is 4.0x10¹4 cm²/s at 1400°C and the activation energy is 580 kJ/mol. Assuming that sintering is controlled by lattice diffusion of Al > estimate the initial rate of sintering for an alumina powder compact of 1 um particles at 1300°C. 30
The following table contains melting temperature (K) and self-diffusion activation energy data for several metals that have the FCC crystal structure. Melting Temperature (K) Activation Energy (kJ/mol) Metal Lead (Pb) 600 107 Aluminum (Al) 933 144 Copper (Cu) 1358 200 Iron (Fe) 1811 284 Nickel (Ni) 1728 285 Make a plot of activation energy versus melting temperature and draw a best-fit line through the data points. Using this plot estimate the self-diffusion activation energy for silver. self-diffusion activation energy = 310.86 kJ/mol
A7