In your laboratory notebook, draw an energy diagram for your semiconductor sample. On your energy diagram, draw the transitions showing the absorption of the blue-violet photon (4.5x10") and the fluorescence (emission) of the yellow photon (3.5x10"). Make sure to adjust the energy diagram (1.e. the single conduction band and the single valence band) on the scale and to adjust your arrows' length and direction so that they are consistent with the photons described.

In your laboratory notebook, draw an energy diagram for your semiconductor sample. On your energy diagram, draw the transitions showing the absorption of the blue-violet photon (4.5x10") and the fluorescence (emission) of the yellow photon (3.5x10"). Make sure to adjust the energy diagram (1.e. the single conduction band and the single valence band) on the scale and to adjust your arrows' length and direction so that they are consistent with the photons described.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Explain why the center of the band is used to calculate the Rf value for a cation rather than the leading edge of the band.
Chemistry Find the maximum draw ratio of the given flexible linear polyethylene samples given in the table below When the chains are crystallized from a solution where the solution concentration is just above the critical overlap concentration | Mw (g/mol) 200000 Polydispersity 1.0 800000 1.0 2000000 1.0 4000000 1.0
9-What type of bonding would be expected of brass (a copper-zinc alloy) • Van der Waals ionic • metallic covalent 10-The Burgers vector is Parallel to the direction of ------dislocation • edge mix screw • all 11-The atoms on the surface of materials are in --------energy state than the interior atoms • lower • higher • equal • equivalent
H2C=CH2 + H2 → CH3CH3 reaction occurs more easily in metal catalysis. Explain the reason according to MOT by showing the orbital overlaps. I've asked this question before, but I couldn't understand it because it's not legible.
3.) At room temperature the electrical conductivity of PbTe is 500 (Q-m)1 whereas the electron and hole mobilities are 0.16 and 0.075 m?/V-s, respectively. Compute the intrinsic carrier concentration for PbTe at room temperature. a) 1.33 x 1020 m3 b) 1.33 x 1023 m3 c) 1.33x 1022 m3 d) 2.13 x 10 m3 e) 2.13 x 105 m3
(b) Shown below are two schematic band diagrams for silicon. Answer the following questions: (i) For phosphorous-doped silicon, draw a dashed line denoting the location of the additional state(s) created by the phosphorus at room temperature. Explain your answer. (ii) For phosphorous-doped silicon, draw a dashed line denoting the location of electrons donated by the phosphorus at room temperature. Explain your answer. Conduction Conduction band band Band Band дар gap Valence Valence band band (i) (ii)
Chemistry If an FCC material terminated at a surface, which plane would give you the lowest surface energy? (110) (111) (100) (200)
One of the following statements related to the conductivity is *not true* : A. Conductivity is a measure of the total amount of dissolved ions in water B. The conductivity measurement of deionized water is an indication of a low resistivity material. C. The Arrhenius dissociation theory assumes the degree of dissociation as the ratio of the molar conductivity to the limiting molar conductivity. D. The molar limiting conductivity is evaluated by the molar conductivity of an electrolyte at its zero concentration
1. For BCC (body-centered cubic) chromium (Cr, having atomic radium of 0.1249 nm), determine the expected diffraction angle (θ) for the second-order reflection from the (211) set of planes, under monochromatic radiation with a wavelength of 0.0711 nm.
9
Explain the Junction potential.