In the shown connection, the coefficient of friction is 0.05. Calculate the minimum allowable  tightening torque to carry the load F=1000N. If high tensile bolt 9.8, calculate the design  factor of safety.

Q: Power square thread lift 10 tons, dm= 40 mm, do= 46 mm & u=0.15 . choose the thread angle (2) that…

A:

Q: Q1: Power square thread lift 10 tons, dm= 40 mm, do= 46 mm & u=0.15. choose the thread angle (2)…

A:

Q: An ACME-thread power screw is considered. The coefficient of friction of the thread is mu. The…

A: Given: The major diameter, d = 1.75 in The screw lead, l = 0.25 in The coefficient of friction, µ =…

Q: :Power square thread lift 10 tons, dm= 40 mm, do= 46 mm & u=0.15 . choose the thread angle (2) that…

A:

Q: A double-threaded power screw is used to raise a load of 5 kN. The nominal diameter is 60 mm and…

A:

Q: An M30 x 3.5 ISO 8.8 bolt is used in a joint at recommended preload, and the joint is subject a…

A: Introduction Bolted joints are a collection of fasteners and nuts used to unite two things into…

Q: A trapezoidal-threaded power screw with a crest diam- eter of 30 mm and single thread is used to…

A: Given : crest diameter, dc = 30 mm  load, W = 50 KN collar mean diameter, D = 40 mm  coefficient of…

Q: 5. Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for…

A:

Q: RB&W¹1 recommends turn-of-nut from snug fit to preload as follows: 1/3 turn for bolt grips of 1-4…

A: Please check the answer in the explanation.     I hope you'll find this helpful.…

Q: In the figure below the clamping force on the pipe is (331.7 lb), knowing that a single threaded…

A: P =331.7lb D=1 inch coefficient of friction (K) =0.2135 for 1030 hot rolled carbon steel tensile…

Q: Two identical 4 in. major-diameter power screws (single-thread) with modified square threads are…

A: Given:f = 0.1fc = 0.24v = 3ft/min = 36 in /minTo find:Power required to drive each screw when the…

Q: For the joint shown below, a Metric grade 8.8 M90x6 screw connects two plates. The joint stiffness…

A:

Q: Design a turnbuckle subjected to a load of 50 kN with permissible stresses are in 166.67 Mpa in…

A: Given Data P=50kN σt=166.67MPaτ=83.33MPaσc=166.67MPa

Q: If I have a singular roller joint, in which total different directions can it provide a force in?

A: A roller joint typically refers to a joint or connection that allows rotation about a single axis.…

Q: esign a clamp coupling to transmit ‘35’ kW at ‘120’ r.p.m. The allowable shear stress for the shaft…

A: GivenPower P=35kWN=120rpmτshaft=τkey=50MPanumber of bolts n=6The permissible tensile stress for the…

Q: A light standard for a highway is shown in figure 6.52. Although it is made entirely of welded…

A:

Q: An M20x1.5 ISO 5.8 bolt is used in a joint at recommended permanent preload, and the joint is…

A:

Q: Q4. Two plates have a length (L) and thickness (t), were welded together. Assume these plates have…

A: Q4: Weld joint: A weld joint is a joint which is used to join two or more plates by adding a fusion…

Q: (7) A clutch system is to be designed to transmit 800 ft-lb of torque. A multi-plate clutch in an…

A: Given:The torque transmitted by the clutch system, The maximum diameter of the outer disk, The…

Q: A link in a mechanism is to be subjected to a tensile force that varies from 3500 to 500 N in a…

A: Soln :- In a given problem we have a link that mechanism is subjected tesnile force which is able to…

Q: 1. A full journal bearing of 150 mm diameter supports a load of 40 kN. The speed of the journal is…

A:

Q: Find the number of bolts M8*1 which made from SAE Grade 4 steel that should be used to provide a…

A:

Q: A 1000N vertical force is applied to the crank of the same diameter as shown. The material specified…

A: To design a structure, we need to first determine the external forces and torques applied to it.…

Q: ad acting on

A: GIVEN:N=1450RPML10h=8000P=5000N

Q: A clamp coupling is to transmit a power of 13 kW to a shaft rotating at a speed of 511 rpm.…

A:

Q: The adjustable height caster is designed to carry 2000 N and operate on the floor that may not be…

A: Based on the information you provided and the image of the adjustable height caster, here's how to…

Q: Pls give right answer with step by step explanation. Design a clamp coupling for a shaft diameter…

A: To design: The clamp coupling. Given: The shaft diameter is d=60 mm. The torsional moment is T=160…

Q: distance ( mm ) measurement between preload and major load position of the Rockwell

A:

Q: 1. A full journal bearing of 150 mm diameter supports a load of 40 kN. The speed of the journal is…

A: Designing the journal bearing.

Q: RB&W11 recommends turn-of-nut from snug fit to preload as follows: 1/3 turn for bolt grips of 1-4…

A: To findthe torque is necessary to establish the desired preload.The turn of the nut.Givenpreload,…

Q: A square thread has a pitch of 3 mm and a diameter of 15 mm.  The coefficient of friction is 0.2.…

A: Given:Pitch of a square thread, p=3 mmDiameter of thread, d=15 mmThe coefficient of friction,…

Q: Find the number of bolts Mg*2 which made from SAE Grade 4 steel that should be used to provide a…

A: The maximum tensile force that may be given to a bolt without causing plastic deformation is known…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.