In the orifice and Jet flow experiment, the following data were collected: Water level = 30 cm, Volume V = {V} L was collected in time 32 seconds, orifice diameter = 6 mm, X1 = 50 mm , X2 = 100 mm, X3 = 150 mm, X4 = 200 mm, X5 = 250 mm Y1 = 3 mm , Y2 = 10 mm, Y3 = 22 mm, Y4 = 38 mm, Y5 = 63 mm What is the actual velocity of water jet that leaves the orifice (m/s)?

In the orifice and Jet flow experiment, the following data were collected: Water level = 30 cm, Volume V = {V} L was collected in time 32 seconds, orifice diameter = 6 mm, X1 = 50 mm , X2 = 100 mm, X3 = 150 mm, X4 = 200 mm, X5 = 250 mm Y1 = 3 mm , Y2 = 10 mm, Y3 = 22 mm, Y4 = 38 mm, Y5 = 63 mm What is the actual velocity of water jet that leaves the orifice (m/s)?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pitot-static tube to be used in 2n airplane for on-flight measurement was calibrated on ground by using air of density 1.20 kg/m? . A measurement taken at an altitude of 3000 m where the ambient pressure and density were 70 kPa (abs) and 0.91 kg/m? respectively, indicated a velocity of 200 m/s by using the above ‘ground level calibration. Estimate the true speed of the airplane [Take k = 1.4 2nd R = 287 J(kg K
Find and show the desired ones.
The data given in the accompanying table represents the velocity distribution inside a pipe. Find the equation that best fits the fluid velocity–radial distance data given. Compare the actual and predicted velocity values. Plot the data first.
Use Excel to plot the following data for a pump. Use two different y axes. Use a scale of zero to 140 cm for the head and zero to 100 for efficiency.
Solve correctly please, will rate for correct ans only.
A bolt weighing 2 kg is accidentally dropped down a vertical cast-iron pipe 4 m long. The lower end of the pipe is closed by means of rigid flange. Calculate: 2.1 The instantaneous stress induced in the pipe if the inside diameter of the pipe is 200 mm and has a wall thickness of 10 mm; 2.2 The instantaneous elongation of the pipe; 2.3 The gradually applied load that would ind
Exercise [2] As shown in Figure below, the velocity of water, v (m/sec), discharged from a cylindrical tank through a long pipe can be computed as: (/2gH V2gH tanh 2L V = L. Where g=9.81 (m/sec?), H=initial head (m), L= pipe length (m), and t = elapsed time (sec). Determine the head needed to achieve v= 5 m/sec in 2.5 seconds for a 4-m-long pipe by Newton-Raphson method. Use ɛ= 1%.
Estimate the Celsius equivalent of Absolute temperature (a) and standard Temperature (b). 19 put of BI三|に Paragraph question Path: p Maximum file size: 100MB, maximum number of files: 1 hp
The water circulates throughout the building in a hot water heating system. If the water is pumped at a speed of 1 m/s through a 6 cm diameter pipe in the basement under a pressure of 200 kPa, sadwhat will be the velocity ( Select] and pressure [ Select ] v in a 3 cm diameter pipe on the 2nd floor that is 5 m above the basement? b. from basement to 2nd floor, what happens to the speed of the water? [Select] c. from basement to 2nd floor, what happens to the pressure of the water? [ Select ]
An engineer would like to create a formula to determine the force exerted by a river flow on a bridge column. The figure of the problem is shown here in front and top views. Front view 18 |h Water properties V, P, μ Top view of This problems is similar but not the same of the exercise I solved in the class notes. Note that there are more variables which may be relevant for this problem, such as the gravity g and the flow depth h. Use the Buckingham Pi Theory to find an expression for the force F. 1) What popular non-dimensional numbers do you see? 2) What is the expression of the force?
the title of the book: Engineering Thermofluids Thermodynamics, Fluid Mechanics, and Heat Transfer by: Mahmoud Massoud
% ParametersD = 0.1; % Diameter of the tube (m)L = 1.0; % Length of the tube bundle (m)N = 8; % Number of tubes in the bundleU = 1.0; % Inlet velocity (m/s)rho = 1.2; % Density of the fluid (kg/m^3)mu = 0.01; % Dynamic viscosity of the fluid (Pa.s) % Define the grid size and time stepdx = D/10; % Spatial step size (m)dy = L/10; % Spatial step size (m)dt = 0.01; % Time step size (s) % Calculate the number of grid points in each directionnx = ceil(D/dx) + 1;ny = ceil(L/dy) + 1; % Create the velocity matrixU_matrix = U * ones(nx, ny); % Perform the iterationsfor iter = 1:100 % Calculate the velocity gradients dUdx = (U_matrix(:, 2:end) - U_matrix(:, 1:end-1)) / dx; dUdy = (U_matrix(2:end, :) - U_matrix(1:end-1, :)) / dy; % Calculate the pressure gradients dpdx = -mu * dUdx; dpdy = -mu * dUdy; % Calculate the change in velocity dU = dt * (dpdx / rho); % Update the velocity matrix U_matrix(:, 2:end-1) = U_matrix(:, 2:end-1) + dU; % Apply…