In the mechanism in the figure; The 2nd limb in the horizontal position rotates with a constant angular velocity of 100 rad/s under the effect of external torque T12.Obtain the equations of change of axial internal force, shear force and bending moment in limb 3 due to inertia and bond forces at the specified position, ignoring frictions.(O2 joint point is the center of gravity of limb 2)

Q: An electric motor is accelerating a 250 kg load with acceleration of 1.2 m/s? through a gear box as…

A:

Q: What would be the stretched length in spring (AB)?

A:

Q: Consider the system shown in the following figure, which is pivoted at point O. Suppose the system…

A: Given:-            Moment about pin:                          ∑M = 0ftb = Mb2+mb23θ.. +cb2θ. +ka2θ…

Q: Find the Grashof condition, any limit positions, and the extreme values of the transmission angle…

A: Given:

Q: Initially h is 269mm, Mass = 15 kg, k= 180 N/m and has unstretched length= 127 mm. Find the…

A:

Q: A jet engine shown in Fig. 3-26 is being tested statically on a test stand. The inlet velocity is…

A:

Q: Find the equivalent translational mass at location A of the system shown in the figure.

A:

Q: To simplify this mechanical process, consider the following diagram (Figure 2). The location of the…

A: given; θ=π3radian   (or) =600crank radius(r)=23cmconnecting rod length(l)=40cm

Q: A two-link mechanism (AB and BC) makes contact with a disk of radius R = 0.1 m at point C (a…

A:

Q: u =0 UnitsTm/s^ 2 umberT-7.4 7.4 j UnitsTm/s^ 2 umber -0.88 f you would like to Show Work for this…

A: Givenmass of slab m1=40kgmass of block m2=9kgbetween block and slabcoefficient of static friction…

Q: 1. Consider the system shown in the Figure P1, where ky is torsional stiffness. Assume that the…

A:

Q: Don't use chat gpt plz

A: Step 1: Step 2: Step 3: Step 4:

Q: The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is…

A:

Q: A) For the adjacent figure': a) Develop the exact and linearized equation of motion by either…

A: Given that

Q: Figure 1.1 shows a crank, OA = 72 mm long which rotates anticlockwise about 0 at w = 150 rev min A…

A: Refer the answer in the next page.

Q: Q3. Derive expressions for the displacements of the masses in Fig. 1 when m₁ = 25 lb- 1, 2, and k, =…

A: Given that-Find:Expression for the displacement of masses.

Q: Consider the system shown in the following figure, which is pivoted at point O. Suppose the system…

A:

Q: The linkage in Figure P7-5b has 0,A = 0,A = 0.75, AB = 1.5, and AC = 1.2 in. The effective crank…

A: GivenO4A=O2A=0.75AB=1.5AC=1.2effective crank angle =77°angle BAC=30°ω2=15rad/sα2=10rad/s2To find…

Q: a crank-slider linkage with the link lengths L2 10 mm, L3 = b = 120 mm, offset = c = тт. = 60° find…

A:

Q: Fig. 10-18 free-body gram for th

A: Consider the free body diagram of the block as shown below. From the free body diagram,

Q: Figure B2 shows a crank driven assembly that comprises three connected slender bars (AB, BC and CDE)…

A: Given: AB=0.3 mBC=0.5 mCD=0.3 mDE=0.6 mθ˙=10 rad/s

Q: R4-13. Determine the force P required to hold the 800-lb weight A by means of the system shown…

A:

Q: To calculate the angular speeds of the two bars B2 and B3, you need to use the two point formula:

A:

Q: A homogeneous siender bar AB of mass m and length L is released from rest in the position shown i…

A: Given: A homogeneous Slender bar of length l and mass m is released from rest position as shown in…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.