Answered: In the laminar flow of air (Pr = 0.7)…

In the laminar flow of air (Pr = 0.7) over a heated plate, if & and 8, denote, respectively, the hydrodynamic and thermal boundary layer thicknesses, then (a) 8 = 8. %3D (b) 8 ~ 8

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Atmospheric air with free flow velocity U_∞= 30 m/s flows through a circular cylinder at T_∞= 250 K and D = 2.5 cm diameter. The surface of the circular cylinder is kept at a uniform temperature T_w = 350 K.The CD drag coefficient is 1.1. (D=1 cm- 3 cm and U_∞= 10 m/sec 30 m/s)(a) Calculate the average heat transfer coefficient ( h ̅_m,W/m2K)(b) Determine the amount of heat transfer (Q, W) per 1 m length of the cylinder(c) Calculate the drag force (FD, N) acting on the 1 m length of the cylinder FD=0.1 A=0.34 D=2.9 cd=1.2
Engine oil at 100°C flows on the top surface of a 1-m-long flat plate maintained at 20°C. The oil’s freestream speed (u infinity) is 0.1 m/s. Find the engine oil properties from the table A.5 A. Evaluate the Reynolds number, local convection coefficient, heat flux and shear stress at the end of the plate (x = L). Is the air flow laminar or turbulent over the plate?B. Evaluate the average convection coefficient, average heat flux, average shear stress and drag force over the plate.
Water (T= 10 C, , k=0.644 W/m.C, u = 5.54× 10^-7 m2/s, Pr=3.55), flow over plate 1m x 1m , with velocity 2 m/s. the plate surfące temperature is 90 C. Give the answer for the following |-the flow tyPe 2-total het transfer 3-theavargeheat transfer cafficient 4- Nu ?
Air at 25 ° C blows over the hot steel plate whose surface temperature is maintained at 150 ° C. The plates are 50 cm x 40 cm in dimensions and 2.5 cm thick. The convection heat transfer coefficient on the upper surface is 20 W / (m² ° C). The thermal conductivity of steel is 45 W / (m ° C). Calculate the hourly heat loss from the plate surface. a. heat loss per hour = Answer kJ. b. If the reverse side surface temperature is maintained, determine the hourly heat loss occurring = Answer kJ.
A high speed train has a design speed of 120 km/hr. A flat plate of length 200 m with a width of 9 m is used for the simulation of train. Determine the approximate power required to overcome surface frictional resistance . ( Air density :1,2 kg m3 viscosity: 1,5 x 10-5 m2/ s )ANSWER: 69,6 k W
Q2: A) Assuming linear variation of velocity in the boundary layer i.e. (u/u) =(y/6), up to y= 8 and then u = u, determine using the integral momentum equation, the boundary layer thickness. B) The temperature ratio: [T,-T)/(T, -T)] = sin (zy/0.015) in flow over a flat plate. If k = 0.03 W/m.K, determine the value of convective heat transfer coefficient.
The heat transfer coefficient is a nondimensional parameter which is a function of viscosity ? , specific heat cp (kJ/kg·K), and thermal conductivity k (W/m·K). This nondimensional parameter is expressed as (a) cp/? k (b) k/? cp (c) ? /cpk (d ) ? cp/k (e) cpk/?
D Eulerian A description Dt System analysis В RTT Fill in th blanks (A, B), |is related through the material derivative to an Eulerian description. Systems analysis is related to analysis using the reynolds transport theorem.
An isothermal long cylinder with square (side of 0.4 m and diagonal of 0.5657 m) cross-section is placed in a flow with a velocity of 1 m/s as shown. The properties of the fluid are: kinematic viscosity is 1.38 x 10-5 m²/s, thermal conductivity is 0.024 W/m.°C, and Prandtl number is 0.73. What is the average Nusselt number for the flow? 1253 a Figure 1: Flow configuration for Problem 6. The dimensions are: a=0.4 m, b=0.5657 m
200 pm 0.12 cm Fluid Stationary cylinder 4 In regions far from the entrance, fluid flow through a circular pipe is one-dimensional, and the velocity profile for laminar flow is given by u(r) = Umax(1 - r/R9), where R is radius of the pipe, r is the radial distance from the center of the pipe, and Umax is the maximum flow velocity, which occurs at the center. Obtain (a) a relation for the drag force applied by the fluid on a section of the pipe length L and (b) the value of the drag force for water flow at 20°C with R = 0.08 m, L = 15 m, Umax = 3 m/s, and u = 0.0010 kg/m.s. %3D
Air at 15°C flows at 10 m/s over a flat plate of length 3 m. Using one-seventh power law of the turbulent flow, what is the ratio of local skin friction coefficient for the turbulent and laminar flow cases? (The kinematic viscosity of air is 1.470 × 10−5 m2/s.) (a) 4.25 (b) 5.72 (c) 6.31 (d ) 7.29 (e) 8.54
A plate is cooled by a fluid with Prandtl number Pr >> 1. Surface temperature varies with distance form the leading edge according to where C is constant. For such a fluid it is reasonable to assume that axial velocity within the thermal boundary layer is linear given by u=V% y Determine the local Nusselt number and show that surface heat flux is uniform. Use a third degree polynomial temperature profile and assume laminar boundary layer flow y YA To Vo T₁(x,0)=T +C√√x U -8 &₁ X T₁(x) = T₁ +C√x