In the following circuit, the BJT Q1 operates in the active region. The amplification factor B = 100 and I₂ = 8 x 10-¹6 A. Determine the following; (a) Ic (b) VBE (c) IE (d) VB

Q: Analog to Digital Converter (ADC) ADC0804/0808 when Vref=5v and when Vref =20v Explain the…

A: Given  Analog to digital converter Ic 0808/0804 .vref=5v and vref =10 v ,we need to enumerate the…

Q: Part IV. Find the maximum peak-peak voltage output without clipping. Present all the results in a…

A: Given data Collector voltage, VCC=15 V Base resistance, RB=280 kΩ Current gain, β=120 Collector…

Q: Assume each diode to be OFF when V₂ ≤ 0.7V and ON when VĎ >0.7V. Find iD1, İD2, İD³, and vō in each…

A: Given:a circuit,when , the diode is off. when , the diode is on. Find:iD1, iD2, iD3 and v0.

Q: *-The transistor of JFET works as resistance change in region All them O Active linear region O Cut…

A: The transistor of JFET work as resistance change region or ohmic region at which drain current shows…

Q: In Analog to Digital Converter (ADC) the input will be in digital form. O a. TRUE O b. FALSE

A: Analog to digital converter (ADC) are the converters that convert analog signal to digital signal.

Q: A Junction FET can be used as voltage variable resistor For any value of drain to source voltage At…

A: Junction FET is usually operated in the portion of its output characteristics where current is…

Q: For the model shown below , if the final value of step input is 5 the display output after run this…

A: The unit step function u(t) is defined as U(t) = {  0,  t<0  } , {1 , t >0 ; } where u is the…

Q: For the circuit given in Figure 2, with R₁ Draw the output voltage waveform at point A. =2k,…

A: According to the question, for the circuit shown belowWe need to draw the output waveform.

Q: Sketch the output voltage for each Zener limiting circuit in the Figure for the following cases: a)…

A:

Q: 24 Explain the advantage of using a 4 to 20 mA current loop as an input signal compared to a 0 to…

A: Explain the advantage of using a 4 to 20 mA current loop as an input signal compared to a 0 to 5-V…

Q: Solve the emitter voltage of a voltage-divider bias circuit with Vcc=9V, R1=560k ohms, R2=560k ohms,…

A: Types of biasing for Transistor  Fixed bias Self bias Voltage divider bias Collector bias Emitter…

Q: To a measurement range of -4 to 6 V, apply a 4-bit analog-to-digital converter. a- Identify the…

A: In given problem ADC is 4 bit hence number of steps(bins) in which analog input is divided is 2n…

Q: Discuss the thermistor

A: Brief description: In the above given question we need to define about thermistors.

Q: Re 1-2 Vo 5Vの Operational omplifier is i deal, what is the output voltgpe of Vo?

A:

Q: With the given circuit below, if the input voltage is 10 volts peak-to-peak and the diode is…

A: The diode is ON when the voltage across anode is more than the cathode voltage. It is known as…

Q: Refer to the following figure. If BDC = 100 and VCE(sat) = 0.1 V , the value of IC(sat) is equal to…

A: By kvl Vcc-Ic(sat) × Rc - Vce(sat)=0 So Ic(sat)= (vcc - Vce(sat))/Rc

Q: 5. In the circuit shown below, if Ro is given, what value must R₁ have in order than the input…

A: The circuit diagram,The input resistance between the terminal is ,

Q: This is a block diagram of a 4-bit analog to digital converter (A/D). Assume the analog input ranges…

A: The detailed solution is as follows.

Q: What happens to cut-in voltage when the temperature increases? a) Cut-in voltage increases b) Cut-in…

A: Option :b ( correct answer)

Q: Explain the operation of the opamp circuit in the figure. In what situations does the LED…

A: An ideal opamp is a differential amplifier with infinite gain. Even though the gain is infinite, the…

Q: What scale value would you use with analogWrite() to generate a average vlotage of 3V on PWM pin 9

A: In electrical engineering, PWM stands for "pulse width modulation," which is also known as…

Q: For Ideal controlled rectifier which one of the following statement is correct? O a. RF and THD…

A: For ideal controlled rectifier which one of the following statement is correct? a.RF and THD values…

Q: Explain and discuss how the clamper circuit with biasing voltage work

A: Brief description : In the above given question they have mentioned a clamper circuit and they want…

Q: Find the voltage of outl and out2. 2K out2 OPAMP OPAMP outl

A: We will find out the output for first opamp then we will find out output voltage for second opamp .

Q: 18) decreasing Vcc in 555-AMV can : O increase charging T1 decrease disch T2 decrease charging T1…

A: The 555 Oscillator:             It is type of relaxation oscillator for the generating stabilized…

Q: Q - 8V + 12V R₁ = 1.2k-2 MM R₂=2.5k om R3 o Vo 56052

A:

Q: 1. Design a combination circuit and write a logic circuit when there are 3 switches and 1 lamp, the…

A:

Q: w.5:Desia The op uoltage is limited to curcenk in ny resisfos is limited to 50MA. (Ans. Ri=40KS,…

A:

Q: This is a block diagram of a 4-bit analog to digital converter (A/D).  Assume the analog input…

A: The solution can be achieved as follows.

Q: In voltage regulators, Zener diodes are used to operate in Select one: a. Reverse mode b. Forward…

A: In forward mode zener diode just acts a normal diode and offers a small forward voltage drop In…

Q: estion about Electronics i have

A: The practical diode carry some internal resistance and some cutting voltage. For forward bias…

Q: for the circuit shown below: The lower reference threshold 10v vin=5 sinwt -10v 3 kOhm 1 k Ohm

A: A voltage reference is an electrical component or circuit that generates a constant DC…

Q: If Vz=8 V and Pzmax=150mW. Determine the minimum value of RL to ensure the Zener diode is in the ON…

A: We need to find out the value of load resistance

Q: In a voltage regulator using Zener diode, the so called line regulation measures the change in…

A: Based on the given definition of the line regulation of the zener diode the validity of the…

Q: At the output of a rectifier connected to a load, O a. A smoother output voltage is an output…

A: In this question,  We need to choose the correct option What is condition to get smoot output of a…

Q: An n-c nmon connguratio (Rp) 61 2.2kN and its transconductance is 3mSiemens. When input voltage is…

A: Given RD = 2.2 Kohm,  gm = 3 mS Vi = 200 mV To find output voltage Vo

Q: ww 2:2 ww Vec www. ☺ W Re UNP Voll

A:

Q: voltage doubler will not provide a A.c. output that is twice the peak input D.c. voltage. true O…

A: Generally in the voltage doubler  circuits the voltage is taken across the capacitor,  so it…

Q: can you give an Introduction about 3 Band Equalizer, the use of it and how it works

A: We have given the problem  can you give an Introduction about 3 Band Equalizer, the use of it and…

Q: please write Details about Verification of series RL series circuit

A: Assume RL circuit  Connect DC supply and AC supply. Write down Verification of series RL series…

Q: Let's assume that 0V when A, B, C, D, E switches are open and 1V when they are closed. What will be…

A: To answer above question, one should know what an op-amp based amplifier circuit is. An amplifier is…

Q: Write the characteristics of ideal opAmp.

A:

Q: In the figure below, find the range of load resistance values that maintain a zener voltage of 10v e…

A: The solution is given below

Q: For the given Zener voltage regulator circuit, Rs 100 2 and Zener current rating is 15 mA. Over what…

A:

Q: Distinguish between combinational and sequential circuits

A: Both the sequential and combinational circuits are commonly and frequently used circuits in digital…

BJT (Bipolar Junction Transistor)

A BJT is a semiconductor device with 3 terminals that consist of a p-n junction diode that can amplify the signal or current. It is a current-controlled device. The three BJT terminals are base, collector, and emitter. The BJT works with the charge carrier, the two type of carriers in the BJT are holes and electrons, the charge carriers flow by the process of recombination. The signal to be amplifier is generally given as the input at the base terminal and an amplified form of it is available at the collector terminal.