In the figure, suppose the length L of the uniform bar is 3.5 m and its weight is 150 N. Also, let the block's weight W = 340 N and the angle 0 = 33°. The wire can withstand a maximum tension of 370 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? C com Ө A B (a) Number 1.3 Units m (b) Number 310.3 Units N (c) Number i691.5 Units N

In the figure, suppose the length L of the uniform bar is 3.5 m and its weight is 150 N. Also, let the block's weight W = 340 N and the angle 0 = 33°. The wire can withstand a maximum tension of 370 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? C com Ө A B (a) Number 1.3 Units m (b) Number 310.3 Units N (c) Number i691.5 Units N

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 64PQ: A One end of a metal rod of weight Fg and length L presses against a corner between a wall and the...

See similar textbooks

Similar questions

An aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0107N/m2 ?
Review. The mass of a car is 1 500 kg. The shape of the cars body is such that its aerodynamic drag coefficient is D = 0.330 and its frontal area is 2.50 m2. Assuming the drag force is proportional to 2 and ignoring other sources of friction, calculate the power required to maintain a speed of 100 km/h as the car climbs a long hill sloping at 3.20.
A painter of mass 87.8 kg is 1.45 m from the top of a 6.67-m ladder. The ladder rests against a wall. Friction between the ladder and the wall is negligible. The ladders mass is 5.50 kg. Assume the ladder is set up according to Occupational Safety and Health Administration standards so that it makes a 75.5 angle with the floor. a. What is the minimum coefficient of static friction required for the painters safety? b. Would rubber ladder tips on dry concrete be safe?
A 20.0-kg horizontal plank 4.00 in long rests on two supports, one at the left end and a second 1.00 m from the right end. What is the magnitude of the force exerted on the plank by the support near the right end? (a) 32.0 N (b) 45.2 N (c) 112 N (d) 131 N (e) 98.2 N
A brass wire and a steel wire, both of the same length, are extended by 1.0 mm under the same force. Is the cross-sectional radius of the brass wire more, less, or equal to the cross-sectional radius of the steel wire? Explain. Youngs moduli for brass and steel are 1.0 1010 N/m2 and 2.0 1011 N/m2, respectively.
Repeat Exercise 5.18 with the contestant pulling the block of ice with a rope over his shoulder at the same angle above the horizontal as shown in Figure 5.23(b).
In Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?
Show that when A+B=C then A2+B2+2ABcos , where is the angle between vectors A and B .
A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.
Why is the following situation impossible? A worker in a factory pulls a cabinet across the floor using a rope as shown in Figure P12.36a. The rope make an angle = 37.0 with the floor and is tied h1 = 10.0 cm from the bottom of the cabinet. The uniform rectangular cabinet has height = 100 cm and width w = 60.0 cm, and it weighs 400 N. The cabinet slides with constant speed when a force F = 300 N is applied through the rope. The worker tires of walking backward. He fastens the rope to a point on the cabinet h2 = 65.0 cm off the floor and lays the rope over his shoulder so that he can walk forward and pull as shown in Figure P12.36b. In this way, the rope again makes an angle of = 37.0 with the horizontal and again has a tension of 300 N. Using this technique, the worker is able to slide the cabinet over a long distance on the floor without tiring. Figure P12.36 Problems 36 and 44.
Which of the following statements is true about the relationship between the dot product of two vectors and the product of the magnitudes of the vectors? (a) AB is larger than AB. (b) AB is smaller than AB. (c) AB could be larger or smaller than AB, depending on the angle between the vectors. (d) AB could be equal to AB.
A uniform ladder of length L and mass m1 rests against a frictionless wall. The ladder makes an angle with the horizontal. (a) Find the horizontal and vertical forces the ground exerts on the base of the ladder when a firefighter of mass m2 has climbed a distance x along the ladder from the bottom. (b) If the ladder is just on the verge of slipping when the firefighter is a distance d along the ladder from the bottom, what is the coefficient of static friction between ladder and ground?