In the figure shown, the 8-ft-diameter cylinder, 3 feet long weighs 550 lbs and rests on the bottom of a tank that is 3 feet long. Water and oil are poured into the left-and right-hand of the tank to depths 2 feet and 4 feet, respectively. Determine, the magnitudes of the horizontal and vertical components of the force that will keep the cylinder touching the tank at A. Ans: FH =749 lb > Fy = 2,134 lbs r 4 ft 2 ft 4 ft A Water Oil =0 75

In the figure shown, the 8-ft-diameter cylinder, 3 feet long weighs 550 lbs and rests on the bottom of a tank that is 3 feet long. Water and oil are poured into the left-and right-hand of the tank to depths 2 feet and 4 feet, respectively. Determine, the magnitudes of the horizontal and vertical components of the force that will keep the cylinder touching the tank at A. Ans: FH =749 lb > Fy = 2,134 lbs r 4 ft 2 ft 4 ft A Water Oil =0 75

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

H.W.1 A steel pipe that contains castor oil (p=1.8624 slug/ft) is 6 ft in diameter. Determine the forces exerted on the portion labeled A-B in Figure below if the pipe is filled halfway. Determine also the location of the forces. Pipe length (into the paper) from joint to joint is 8 ft. 6 ft Fy Ih Fx A A A
Dětérmine the magnitude of the force P, acting as shown, that will cause the 120 N crate to move. Assume the coefficient of static friction between the crate and the ground are ps = 0.3. 120N O 45 N O 50 N O 20 N O 36 N
To keep the box from sliding down the plane you applied a certain force P. The box weighs 490.50 N, and the static friction coefficient between the crate and the plane is ms = 0.25. Determine the value of force P. Answer = _N 175 O 155 135 O 150 165 170 30° O 140 O 160
Q6. For figure below, calcu late the forces on surfaces A $ B. surface B (area = 0.1m) air 2 wn water surfae A Caren = o.2 m)
Situation 22: The 125-kg concrete block A is released from rest in the position shown and pulls the 200 kg log up the 30" ramp. If the coefficient of kinetic friction between the log and the ramp is 0.5, compute the following: Sit kp rac fri ca Si 200 kg u HA3D0.5 T 125 kg 6m 30° 1 2 1. acceleration of block A as it hits the ground 2. tension in the cable supporting block A 3. velocity when block A hits the ground
Engineering MechanicsThe blocks shown in Fig. P-522 are separated by a solid strut which is attached to the blocks with frictionless pins. If the coefficient of friction for all surfaces is 0.20, determine the value of horizontal force P to cause motion to impend to the right. Assume that the strut is a uniform rod weighing 300 lb.
m10
The tank shown has one curved surface restraining a body of static fluid with 3.55 kPa air pressure above the fluid and sg = 0.88, with the following dimensions: w = 5.50 m h1 = 2.1 m D1 = 0.85 m Required Compute the magnitude of the resultant force, in kN, to the nearest 100th. Fluid sg = given hl D1
Knowing that P is 24 kN, applied to both sides of the bar at B and Q is 45 kN, applied to the bar at C as shown. What is the internal normal force acting on a vertical cross-section passing through the bar between points A and B? Express your answer in Newtons (not kN), to the nearest whole Newton, taking tension as positive and compression as negative.
Please kindly answer all...all are one question. Figure given below Three identical cylinders are stacked within a rigid bin as shown in the figure. Weight of each cylinder is 500 N. There is no friction at any contact surface. Determine the force at A. a. 122.98 N b. 213.37 N c. 288.68 N d. 391.25 N Determine the force at B. a. 455.67 N b. 673.12 N c. 516.27 N d. 750.00 N Determine the force at C. a. 144.34 N b. 213.87 N c. 197.67 N d. 249.65 N Please show solution, thank you!
need asap, thank you!
I need the answer as soon as possible