In the equation z = ct + d, z is measured in meters and t is measured in seconds. What are the dimensions (units) of d? m-s O s O m/s O m O s/m

Q: A tank is in the form of a right circular cylinder with hemispherical ends. The overall length of…

A: Given:-

Q: A set of sprockets is constructed, as shown in Figure 1, so that the second and third rotate on a…

A: Solution: Given Data: r1=1 cmr2=4 cmrc=1 cmr3=3 cmN1=y rpmN2=u rpmN3=x rpm   To Find: (a) N1N2(b)…

Q: As shown in the figure, A and B are sliding along the horizontal bar with velocities VA = 2 m/s and…

A: Draw the velocity diagram of the system. Here, the velocity bars ac and bc are perpendicular to the…

Q: 27. You have the following compound machine. 60 teeth 40 teeth 20 teeth a. What is the speed of Gear…

A:

Q: The velocity of the piston is 52.9901 3 ft/s.

A: use sine rule

Q: How would you solve this manually without an equation solver

A:

Q: '. An offset slider-crank mechanism is shown in he figure at an instant. Conventionally, the Quick…

A: Given   Length of connecting rod,  L = 40 mm                        Crank radius, R = 20 mm…

Q: ven questions are subparts.. Kindly solve all a, b, c and d all answers otherwise leave it. Thank…

A: A) length of link AB=6002+3002                               =670.0 mmvelocity of point B=VB→ or…

Q: You are given two shafts of equal lengths and made from the same material: a hollow shaft, with an…

A:

Q: Calculate the mechanical advantage of the following compound machine.

A:

Q: reciprocating saw needs to move the blade downward 0.75 in in 0.10 s anc turn in 0.08 s. Determine…

A: As per company's guidelines we can answer only 1st question

Q: Above is a 5 speed manual transmission gearbox. The gear selector fork is an assembly which the user…

A: Gear ratio is defined as ratio of driven gear's teeth to driver gear teeth. G1/2 = T2/T1 G1/3 =…

Q: . VELOCITY ANALYSIS. For the single-degree-of-freedom mechanism shown below, the angular velocity on…

A:

Q: create 2 fourbar designs that include the dimensions and angle of motion

A: It is asked to draw four bar mechanism with given motion

Q: An 18 teeth sprocket driving with 98 teeth sprocket at a center distance of 34 pitches. Find the…

A: Approach to solving the question: Detailed explanation: Examples: Key references:

Q: You need to design a clock using a DC motor that has a constant speed of 3000 rpm. Determine: How…

A: - to design a clock using a DC motor that has a constant speed of 3000 rpm. N = 3000 rpm

Q: Answer the following in the space provided. 39. Suppose the engine in a vehicle is delivering 550…

A: Data given-  T1 = 550 lb -ft  N1 = 5000 rpm  Gear ratio = 1.5/ 1 = 1.5

Q: The torque of a rotated gear wheel is MB = 10 Nm and the torque of the rotating wheel is MA = 50 Nm.…

A:

Q: in the given system, as the result of AB crank arm's spinning, F gear is starting to have an…

A:

Q: In a slider crank mechanism (schematic shown the figure), the crank rotates at 60 revolutions p…

A:

Q: A gear train consists of three gears: a pinion (which is the driver), an idler, and a gear (which is…

A: Given:- The gear train of three gears Tidler=68  Tidler(to replace)=37 To find:- Velocity ratio…

Q: For the quick-return mechanism shown below, the rod DC rotates with a constant angular velocity of 1…

A: For the solution refer below images.

Q: My Home Duty 2: Found in a cylindrical turning process of a 24mm round shaft, the life of the…

A: Taylor's Tool lofe equation gives the direct relation between life of the tool(T) in minutes and…

Q: FIND THE DEGREES OF FLEDOM OF THE MECHANSNE.

A:

Q: An engineer is creating a solid model of a simple gear using SolidWorks. Choose the correct…

A:

Q: From the figure shown. To determine: a) Piston force BC b) Piston force FE c) Pin force G and J d)…

A: Consider the free body diagram of bucket is shown below, Taking moment about point J, ∑MJ=020000…

Q: If the torque and speed values are 125 N-m and 1800 revolution per minute, then the power required…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: For the reciprocating saw shown in the figure below, use the RELATIVE VELOCITY METHOD to…

A:

Q: 1. In the given figure, gear 1 has 24 teeth and gear 2 has 70 teeth of PD=4. Gear 3 has 20 teeth and…

A:

Q: Q2. Figure Q2 shows a simple gear train. At the instant shown, a force F = 1100 N is applied at one…

A: Force F=1100 NTeeth on gear ATeeth on gear BLength of the leverMoment of inertia of the gear A…

Q: (i) Calculate total time taken for the cam to complete a full circle motion. (ii) Calculate the…

A: As per honor code and answering guidelines I can answer 1st 3 subparts at a time.If you want other…

Q: Find the ratio for the tool P and Q

A: Given data,  Two tools P and Q have signatures       50-50-60-60-80-300-0 and…

Q: Calculate the mechanical advantage of the following compound machine.

A:

Q: Three blocks A, B, and C and a grooved block D have dimensions a, b, c, and d as follows: a =…

A:

Q: A 1725 rpm electric motor is to be used to drive a "flat belt" conveyor in a manufacturing facility…

A: The speed of the conveyor belt is, The diameter of the roller is, The number of teeth on the drive…

Q: A.) A cutting operation is performed on a piece of metal. The rake angle of the tool, α, is eight…

A:

Q: In the gear train shown gear 3 is carried on arm 5, Gear 3 meshes with gear 2 and gear 4. The number…

A: Here, Gear 2 is sun gear. Gear 3 is planet gear. Gear 4 is annular gear. Link 5 is arm.   From the…

Q: agine two ordinary gears of different diameters meshed together, with the larger being the driver.…

A: Given:Z1=108 ω1=5.80 rad/sZ2=20

Q: The vertical distance above a reference datum to a point is called the point’s

A: ▪︎We have to specify the term related to the vertical distance above the reference datum to a point.…