A tank is in the form of a right circular cylinder with hemispherical ends. The overall length of the tank is 3 meters and the diameter of the hemisphere is 1 meter. If a pump discharges a fluid whose density 1.2 kgm/L in this tank at a rate of 250 liters per minute. Determine a.) Weight of liquid inside the tank if it is half full. b.) total time to fill the tank assuming it is initially empty.

Q: 4a) A Ship must discharge a total of Seawater ballast 2200 cubic meters of Within 6 hours. Using S…

A: given; (a)discharge volume=2200m3at time (t)=6 hours                  =6*3600 secdiameter of…

Q: 1. Outcome #3. You must show and explain all work. A speed boat utilizes a jet pump for propulsion.…

A: Given: Thrust force (F) = 130 kN = 130,000 N Inlet area at station 1 (A1) = 0.07 m² Velocity at…

Q: 1st: Using the formula t=24(/h3/h2) determine the "A" of tank Caa/2g coefficient of discharge. Note:…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: You work for the Marvellous Toy Company, who manufacture toy plastic figurines and dolls. State what…

A: In a toy company where the molten polymer is required to be pumped, we have to use a high power…

Q: As water is flowing from a water tower to someone house, water is flowing at a speed of 3 m/s in a…

A: Water velocity at 0.3 m diameter, V1=3 m/s Gradual increase in diameter, d2=1.8m Gradual decrease in…

Q: Q3)A tank 6 m long 3 m wide and 2 deep contains oil to depth of 1.75 m .If it accelerated…

A: Given-Data:- The length of the tank= l = 6m Width of the tank = 3m Depth of the tank=2m Horizontal…

Q: Diesel fuel with a specific gravity of 0.8, flows through the Venturi meter shown in figure below.…

A:

Q: The pressure of water in a pipeline was measured by means of a simple manometer containing mercury.…

A: Given data: Height of water in the left column, hw = 45 mm. Height of mercury in the right column,…

Q: 1) M H h On the cylindrical container above with a cross section area A we open a hole as shown with

A: Givencylindrical container below with A=cross section area of container Ah= area of the hole

Q: You are asked to explore the operating principles and efficiencies of hydraulic machines. You have a…

A: As per the guideline, I am solving on part A and B. For rest parts, re-post in a separate post. a)…

Q: For the siphon shown, use Bernoulli's equation to calculate the following. (Assume no friction or…

A: Here, the pressure asked are guage pressures. Dont take absolute pressure. The solution is provided…

Q: Water flows through a in a constant diameter pipe shown below with the help of pump. What will…

A: It is required to determine effect on velocity

Q: Problem 4 A partly full water tank admits water at 85 N/s weight flow while ejecting water on the…

A:

Q: A cylindrical container is filled with a liquid until it reaches a height of one meter with respect…

A:

Q: Water is stored in a pressurised container at a height Нт = 9 m. It then moves through a horizontal…

A:

Q: A 5 lbm ball starts rolling up a 30deg incline at speed of 20 ft/s. Using conservation of energy,…

A: Given   Mass, m = 5 lbm       Angle = 30o Velocity, v = 20 ft/s Find  Power, P

Q: A brand of toothpaste is made using a mixture of white and red paste. During the manufacturing…

A:

Q: 1.39. Air flowing in a 4m x 6m rectangular duct has the following idealized velocity distribution:…

A: Average velocity - it is defined as the change in displacement divided by change in time by the…

Q: Inlet and throat diameters of a horizontal venturimeter are 250 mm and 100 mm respectively. The…

A: Inlet diameter, d1=250 mm=0.250 m Throat diameter, d2=100 mm =0.100 m Pressure at inlet, P1=15…

Q: A cylindrical tank is filled with water at the rate of 5,000 gal/min. The height of water in the…

A: Given data: Q=5000 gal/mint=15 minh=20.42 ft Need to determine the diameter of the tank.

Q: oose the correct answer   3- when the flow is happened without change in its quantity or velocity…

A: Given Data⇒ Flow velocity time

Q: A water system of 2 inches (inside diameter) pipe, having a length of 1/4mile, is to be flushed with…

A: Given Data: The inside diameter of the pipe is, d=2 in=2 in×ft12 in=16 ft. The length of the pipe…

Q: Prototype of a mixed flow mini heart support pump at n1= 11000 rpm the manometric pressure height is…

A: Given data: Calculate the density of the fluid as follows:

Q: resultant force vector acting on the body to be derived. Figure 2 shows a steady, uniform…

A: Impact of jets : Let us consider that we have one pipe through which liquid is flowing under…

Q: II. Problem solving Air 1.) Water flows through a horizontal plastic pipe with a diameter of 0.2 m…

A:

Q: 5. Write down the Benoulli equation and explain the meaning of each terins 6. Water is flowing…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: A differential mercury manometer is used to measure the pressure drop across an orifice meter as…

A: please refer handwritten solution

Q: In a liquid transmission pipeline, a pump had been designed for a throughput of 10,000 bpd. However,…

A: Initial Pump Demand = Q1 = 10000 bpd   New Pump Demand = Q2 = 1.25×Q1 = 12500 bpd   Original…

Q: The test setup shown in the figure measures the pressure difference between the inlet and outlet of…

A:

Q: If the velocity of a liquid is 1.65 ft/s in a 12-inch diameter pipe  What is the speed of a 3-inch…

A: The initial velocity v1=1.65 ft/s The initial diameter d1=12 in The final diameter d2=3 in

Q: a).kN/m2.  b) Head of water in meters,

A:

Q: When a steel ball is placed on the surface of mercury, it does not sink because: A) of the surface…

A: As, is known that the density of the steel ball is 7860 kg/m3 And, density of mercury is 13800 kg/m3…

Q: Helium is supplied in high pressure tanks. If I have a 10-liter tank at 200 atmospheres of pressure,…

A: Introduction In this problem, we will determine the number of 3-liter balloons that can be filled…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.