1) M H h On the cylindrical container above with a cross section area A we open a hole as shown with

Q: Q4/ a) Draw the free body diagram (FBD) b) Find the reactions at O 4 ft 5 ft 35 2 ft 900 N

A:

Q: Sir Edward decided to replicate the experiment of Torricelli (see diagram). He immersed a tube with…

A: d (diameter of tube)=3mmθ (angle formed at the mercury air interface)=51·σ (Surface tension at the…

Q: A block of metal has a 90° notch cut from its lower surface. The notched part rests on a circular…

A:

Q: %) Find the moment of force about point A as shown in Figure? 10 m B 90° 8 m 1000 KN 20°

A: GIVEN DATA- A FORCE SYSTEM SHOWN IN FIG WE HAVE TO FIND MOMENT ABOUT POINT A

Q: Q2: Find the reactions forces at support A and the tension in cable for the beam shown in figure…

A:

Q: A red pickup track towing a white trailer via a ball-and-socket joint at D. a) Find the reactions at…

A: Taking this part Applying the Equilibrium condition ∑nMA=0…

Q: The sides AB and CD of a quadrilate 2. ABCD are extended to points P and respectively. Is ZADQ+ ZCBP…

A: Following are some standard geometrical figure 1) Triangle 2) Rectangle 3) Circle 4) Quadrilateral A…

Q: s lowest point to the ground. Choices: 150m ,153m , 148m , 145

A: length = 300m   weight = 600kf   tension = 4ookg , 450kg

Q: Q1. The structure shown in the sketch is used to pull a load. The force that the load exerts at…

A: The internal forces can be found out by considering either of the sides of the section EE. It is…

Q: Homework 1: Find the resultant of the distributed and concentrated loads as shown in the figure. 8…

A:

Q: 2 m 1 m For the figure below, the center of :gravity is y₁ 2 m 3 m X'= 2.65 AND Y'= 1.217 O X'=1.217…

A:

Q: M M M M L- 5e FIG. 2. Problem 2 Find D in the above figure in terms of 0, and L.

A:

Q: Figure Q3 above shows the schematic of a motor on the right pulling the mass on the left. It is…

A:

Q: A trench is constructed from 5 steel plates. Each plate is 1m X 1m. Plates A,B, and C are horizontal…

A: To Find : The moment about the axis from point G to H. Given:  The dimension of plate is A=1m·1m.…

Q: W T As shown in the figure, two sides of a semicircular trough are hinged to each other at the…

A:

Q: Find the tension in string A and the force B exerted on the string by the beam in the figure.

A:

Q: Q3: Find the second moment of area for the following cross section about (x) neutral axis. 200 mm 50…

A:

Q: A square plate with sides 1.5 m in length can rotate around an axle passing through its center of…

A: Given Data Force acting at top left edge is: F1=30 N Force acting at the bottom left edge is: F2=20…

Q: Q3/ Find the area of the region enclosed by the parabola y² = 8x and the line y=2x.

A:

Q: A motorized cable car weighs 1 MT, carrying a loadP is traveling along a straight horizontal cable…

A: given; ⇒mass of car (m)=1MT                  =1000kg⇒weight of car (w)=mg…

Q: h) The figure below shows a beam supported at points A and B. The vertical force at F is 500 N and…

A: In this issue, we will determine the distance (s) necessary to balance the beam by first calculating…

Q: 1. Three cubes of side l0, 2l0, and 3l0, are placed next to another (in contact) with their centers…

A: 1.a) Position of the centre of the mass from the left side is 3.83l0. b) New mass density would be…

Q: (Q3] (a) The wooden rod AB supports the roof ADC. If the mass of roof is 70 Kg and its weight acting…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: 1.45 The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: solve for the reactions at A and B

A:

Q: Aluminuni rod E 70 GP L 0.7 m A-5 cm² Steel rod E-210 GPa L-1.4 m A= 10 cm? Fig (F)

A: To determine the distance x.

Q: (Q3] (a) The wooden rod AB supports the roof ADC. If the mass of roof is 70 Kg and its weight acting…

A:

Q: the vector approach determine: a) the moment about point “B", b) the moment about point “A", and c)…

A: Given: To determine: Moment about B Moment about A Moment about O

Q: B: Find the total moment of force with respect to point (A), for the two forces in next fig. 8m 3m…

A: Answer: The total moment of force with respect to point (A) is 0 N•m.

Q: Second moment of area The second moment of area employed in the equation to calculate maximum shear…

A: Given : The shear force in this section is The diagram is,

Q: b) A 3500 N crate is being unloaded unto a truck by a crane (Figure 1). The rope AC is tied to the…

A:

Q: 20 in. 40 in. 20 in. Figure shows a homogeneous body. 20° a. Draw the FBD 2400 lb-in. 30 in.…

A:

Q: 50 mm 200 mm 50 mm Neutral Axis (N.A) 25 mm Reference Line For the cross section shown, find: 1- The…

A:

Q: Find the reactions for the followings 3 kN/m B A 3 m 2 kN/m 4 m C

A:

Q: ust for checking determine if true or false 1.) The cross-sectional area of a body is its total…

A:

Q: 13.) Cords are loop around a small spacer separating two cylinders each weighing 400 lb and pass, as…

A: GIVEN DATA WEIGHT OF CYLINDER W=800lb WE HAVE TO FIND ANGLE AND NORMAL PRESSURE N

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.