In the design of a spring bumper for a 3500-lb car, it is desired to bring the car to a stop from a speed of 5 mi/hr in a distance equal to 6 in. of spring de- formation. Specify the required stiffness k for each of the two springs behind the bumper. The springs are undeformed at the start of impact.

In the design of a spring bumper for a 3500-lb car, it is desired to bring the car to a stop from a speed of 5 mi/hr in a distance equal to 6 in. of spring de- formation. Specify the required stiffness k for each of the two springs behind the bumper. The springs are undeformed at the start of impact.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 2.00-kg slender rod shown is hanging in a vertical position and is pin-supported at point A. The slender rod is initially at rest until a 1.000-kg block C, strikes it at its end at point B. The block slides on a frictionless surface with a velocity of 3.50 m/s to the right. After the impact, it slides with a velocity of 1.250 m/s to the right, and the bar rotates with an angular velocity, w'. 3.5 m/s с B 1.5 m Answer the following questions given the picture. Please show clear solutions, I want to learn how to solve the problem. 1a. Which of the following gives the correct kinematic relationship relating the final velocity of the center of the rod, v'G, and its angular velocity, w'? A) 1.333 w' B) 0.667 w' C) 1.500 w' D) 0.75 w' 1b. Which of the following gives the closest value of the magnitude of the horizontal impulse at the support at point A? A) 1.125 N-s B) 1.350 N-s C) 0.1180 N-s D) 2.25 N-s
B8
The 28-lb collar A is released from rest in the position shown and slides with negligible friction up the fixed rod inclined 28° from the horizontal under the action of a constant force P = 52 lb applied to the cable. Calculate the required stiffness k of the spring so that its maximum deflection equals 6 in. The position of the small pulley at B is fixed. P B 28" 28° 6" Answer: k = i 35" lb/ft k
3. Blocks AA and BB of mass 10 kg and 4 kg respectively, are placed on the inclined plane and released. The coefficients of kinetic friction between the blocks and the inclined plane are μAμAmuA = 0.1 and μBμBmuB = 0.5. Neglect the mass of the link
The W1= 69.01-lb block shown rests on a smooth plane (coefficient of kinetic friction = 0) with an angle of θ=34∘ from horizontal. It is connected by a flexible inextensible cord that passes around weightless, frictionless pulleys to a support. The W2 =134.93-lb weight is attached as shown. After the system is released from rest, in what distance will the block on the plain attain a speed of 10.0 ft/s?
The motion of the 5.00-kg uniform rod AB is guided by small wheels of negligible mass that roll on the horizontal and vertical surfaces shown. A spring of constant k = 430 N/m is attached to end B of the rod. The rod is released from rest when 0 = 30° (Position 1) and gets pulled down by the initially deformed spring. When 0 = 45° (Position 2), the spring is at its undeformed length. Hint: Irod = 1/12 mL² 1. Which of the following force/s does/do work on rod AB? 1. Normal force on roller A II. Normal force on roller B III. Spring force at B IV. Weight of rod AB B 2. Which of the following best approximates the value of the elastic potential energy of the system at Position 1? 0.6 m 3. Which of the following best approximates the work done by gravity on the rod during its motion from Position 1 to Position 2? 5. Which of the following best approximates the angular speed of the rod at Position 2? A 4. Which of the following expressions gives the kinetic energy of the rod at Position 2 in…
IV. For the following system that starts from rest, the spool has a weight of 300 N and a radius of gyration ke = 0.3 m, and block A is attached to it as shown of weight 200 N. A constant horizontal force F is applied to the cord in order to give the block an upward speed of 5 m/s. (Neglect mass of cord and tension force). -F 1. Draw the free body diagram of the system. 2. Calculate the angular speed of the spool at t= 6 seconds. 3. Calculate the vertical reaction force at the pin at t= 6 seconds. 4. Calculate the horizontal force F.
A vehicle having a wheel base of 3.2 m has its centre of mass at 1.4 m from the rear wheels and 55 mm from the ground level. It moves on a level ground at a speed of 54 km/h. Determine the distance moved by the car before coming to rest on applying the brakes to the (i) rear wheels (ii) front wheels (iii) all the four wheels The coefficient of friction between the tyres and the road is 0.5. ve
Part A The 200-lb wheel has a radius of gyration of kg = 0.75 ft. The upper wire is subjected to a tension of T = 90 lb. The coefficient of kinetic friction between the wheel and the surface is u = 0.1. (Figure 1) Determine the speed of the center of the wheel in 3 s, starting from rest. Express your answer to three significant figures and include the appropriate units. HẢ vG = Value Units Submit Request Answer Provide Feedback Figure 1 of 1 0.5 ft 1 ft
HW8 The arms of a Porter governor are 310 mm long. The upper arms are pivoted on the axis of rotation. The lower arms are attached to a sleeve at a distance of 20 mm from the axis of rotation. The mass of the load on the sleeve is 95 kg and the mass of each ball is 10 kg. Determine the equilibrium speed when the radius of rotation of the balls is 220 mm. If the friction is equivalent to a load of 21 N at the sleeve, what will be the range of speed for this position and Sensitiveness of Governors?
- Please Help!!