In the design of a control mechanism, it is deter- mined that rod AB transmits a 260-N force P to the crank BC. Determine the x and y scalar components of P. Ans. P, = -240 N Py = -100 N P = 260 N A 12 30°t - x

In the design of a control mechanism, it is deter- mined that rod AB transmits a 260-N force P to the crank BC. Determine the x and y scalar components of P. Ans. P, = -240 N Py = -100 N P = 260 N A 12 30°t - x

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.73P

See similar textbooks

Similar questions

- 1.5 kN-m =-0.9 F+0.6 F3D2.33 kN Example The device shown is a part of an automobile seat- back-release mechanism. The part is subjected to the 4-N force exerted at A and a 300-N-mm restor ing moment exerted by a hidden torsional spring Determine the y-intercept of the line of action of the single equivalent force. א 4_F 10 mm 15 40mm 300 N-mm
4:48 68 O E B18 Statics_Moment.. o 240 N 2. A prybar is used to remove a nail as 15° shown. Determine 350 mm the moment of the 240 N force about the point o of 65° contact between the prybar and the small support block. 30 mm PROBLEMS 240cos10=236.35 N Mo=? 240 N 15° 65 240sin 10=41.68 N 350 mm M=236.35(0.35) +41.68(0.03)=83.97 N -m 65 (clockwise direction) 30 mm PROBLEMS 900 mm 700 mm 3. An experimental device imparts a force of magnitude F = 225 N to the front edge of the rim at A to simulate the F 300 mm effect of a slam dunk. Determine the moments of the force F about point O and about point B. Finally, locate, 3050 mm
touch & OL166% 00:27 MENG250 - Practice Assi... Not saved yet •2-77. Determine the magnitude and coordinate direction angles of F, so that the resultant of the two forces is zero. Y2 B2 a2 y 60° 15°. F= 180 N O
2. Given the cantilever framework below, find the shortest distance from point B to line AC and to line AD. 8' A 3. In the system shown below, determine the length of the common perpendicular between lines AE and BD. Solve in two ways. W = 2200 Ib 4. If the magnitude of a force P acting from A to D is P = 20V73 Ib, determine the component of P that is perpendicular to the plane defined by points E, A, and C. 10' B
The force vector F has a magnitude of F = 385 lb and acts at point A at an angle 0 = 17.8° with respect to vertical as shown. The force F is balanced by the tension forces parallel to the two rods AC and AB such that the vector equation F+FAC+ FAB = 0 is satisfied. Determine the tension forces in the two rods in Cartesian components. C mintono cc) + Ⓡ BY NC SA 2013 Michael Swanbom Variable Value 4.6 ft 2.7 ft 4 ft a b C FAB F Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. FAC= a = For the component notation, use an 'xy' coordinate system with 'y' poining up and 'x' pointing to the right. î A + 0 + b B 3) lb 3) lb
1. Determine the magnitude and direction with respect to the +x axis on the reaction at A and at C. Note that the body is supported by pin at A and a roller at C. The body's weight is negligible. A 2.4 kN-m 400 40° 200 250- Dimensions in mm -300- B 3 kN
3-In the scheme below, 4 objects are hanging from each of the rings and 5 ropes (blue) keep the entire scheme in balance. The known values are m1=30 kgm1=30 kgα=60ºα=60ºβ=30ºβ=30ºγ=70º a) Attach the force diagram on each of the rings with the graphical decomposition of the forces that are not exclusively on the Cartesian axes. b) Determine the tractions T1, T2, T3, T4 and T5. c) Determine the mass of weights 2, 3, 4 and 5. Tip: If you feel comfortable, use software to solve the systems of equations.
Q: The door is held open by means of two chain. if the tension in AB and CD is FA= 300N and Fc= 250 N, find the components of force FA. * 1.5m 2.5 m \Fc= 250 N A F= 300 N 30 D 0.5 m B FA= 280j - 93k FA= 285j - 93k FA= 280j - 92k
DUE NOW. Please answer it correctly. Thank you!
QI/ The rigid pole and cross-arm assembly is supported by the three cables shown. A turnbuckle at D is tightened until it induces a tension T in CD of 1.2 kN. Express T as a vector. Does it make any difference in the result which coordinate system is used? Ans. T = 0.321li + 0.641j – 0.962k kN, IC B 1.5 m G 1.5 m A T= 1.2 kN 3 m 2 m 1.5m
Needs Complete typed solution with 100 % accuracy.
1b. IF x=2.1m and z=1.8m, determine the j component of the unit vector u_AD. Answer must include 3 places after the decimal point. 1c. If x=2m and z=1.5m, find out the correct equilibrium equation (Newton's 1st law) for the force components along the y axis. T_B is the tension force in cable AB, T_C is the tension force in cable AC, and T_D is the tension in cable AD. 1d.If x=2.1m and z=1.5m, and the mass of the flower por is m=34kg, determine the tension force T_B in cable AB. Answer mus include 1 place after the decimal point and the proper unit. Take g=9.81 m/s^2