In the cage system connection in the figure; Rod forces S1 = 90 kN, S3 = - 80 kN, S5 = 70 kN. If joint D is in equilibrium in itself, calculate the strength of the rod S4. Note: The (-) sign of the bar force S3 indicates that the force is pressure. A) 84,853 B) 113,137 C) 42.43 D) 70.71 E) 36.36

Q: A) Draw the free body diagram of Joint C. B) Use the joint method to solve for the forces in truss…

A:

Q: 350 mm 600 mm 400 mm 600 mm. 550 mm 400 mm 450 mm 1600 N A) Draw a free body diagram of the Rod. B)…

A: Find the tension in the cables and reaction at the joint

Q: Force P is supported by two cables and a bar. Point A lies in the yz plane, and points B and C lie…

A:

Q: Write and explain all calculations involved. ps/ Please write it with simple handwriting so i can…

A:

Q: 275 mm 30 30° E 0.5m FHE A) d=0.275 500 mm C D 0:5m 500 mm B) d=0.5 300 mm C) d=0.5*cos30 friction…

A: If a force F is inclined at an angle θ with the horizontal, then the component of force along the…

Q: A steel rod is acted upon by the loading shown below. 50 mm² is the area of the circular rod. The…

A: Hi, I have calculated the asked using the superposition principle. You only have to find the force…

Q: Q2/ Knowing that the forces values given as: F1=32 N, F2=D45 N, F3=60 N, x1=D0.7 m, x2=0.4m, H=1.5m.…

A: For the Given system of forces  F1 = 32 N, F2 = 45 N, F3 = 60 N, x1 = 0.7 m, H = 1.5 m, x2 = 0.4 m…

Q: The axle radius is 1 m and the wheel radius is 4 m.  A 1600-N load is attached to the axle via a…

A: To maintain static equilibrium, the following three equations must be satisfied: 1. The summation of…

Q: E 2m + 2m + 2m 1.5m B D 2m A 2 kN 2 kN 2 kN 1) a) Determine the force in members CE, BD, and CD and…

A: Given: The diameter of the pin at A and G, d = 2 cm = 0.02 m

Q: Q3) Determine the components of reaction at the roller support A and pin support C. Joint B is fixed…

A:

Q: Given the Frame as shown below. Using Method of Members, determine the following if the External…

A:

Q: Figure 2 shows the beam is loaded by distributed loading and supported by the cables DB and DC as…

A: Given: The intensity of udl, w = 800 N/m

Q: 2. For the frame shown, a) Solve for the reaction at the roller support at A and the horizontal and…

A:

Q: The system given in the figure is in balance with the help of the wire in the middle, which is…

A:

Q: Problem 6.2 Rigid Body Equilibrium The tailgate of the vehicle is only supported by a single cable…

A: According to the given data Weight of the blobk=WB=32x9.81=313.92N Weight of the…

Q: Two cables are tied together at C and are loaded as shown. a) Draw and label a Free-Body Diagram of…

A:

Q: RSL-2 A rod of negligible mass is pulled down at each end as shown to the right. The rod is…

A:

Q: Determine the forces in members a) AB, b) AG, c) GF, d) BF, e) BC. Show solution in a letter-size…

A: Given data W1= 13 (kips) W2  = 9(kips) B  = 35(deg) A  = 7(deg) L1= 3 (ft)  L2 = 6 (ft) L3= 7 (ft)

Q: wo rollers of the same diameter shown are supported by an inclined plane and a vertical wall. If all…

A: To calculate the reaction forces at point A, B and C, we must first create the free body diagrams…

Q: A) Draw the free body diagram of Joint C. B) Use the joint method to solve for the forces in truss…

A:

Q: Q1/Determine magnitude of force at DA and GF members by using a) joint method b) section method C B…

A: For the solution refer below images.

Q: Determine: a) The magnitude and direction of the reactions at 3 and 5 b) The forces in each member…

A: Given: Find:a The magnitude and direction of the reactions at 3 and 5b The forces in each member of…

Q: The bracket BCD is hinged at C and attached to a control cable at B. For the loading shown in the…

A: ◆ The tension in the cable is 2000 N. ◆ Therefore, the correct answer is option is (C).

Q: TRUSS PROBLEM Determine: a) The magnitude and direction of the reactions at 3 and 5 b) The forces…

A: To find - a) The magnitude and direction of the reactions at 3 and 5. b) The forces in each member…

Q: Determine the magnitude of the pin reaction at A in kN. b) Determine the magnitude of the pin…

A: Given: To determine: The pin reaction at A  The pin reaction at B  The pin reaction at C

Q: Q4) Structural Analysis This bridge is made of two-force members attached at the ends. All angles…

A:

Q: -200 mm - 350 mm B 200 mm C. A) Draw a Free Body Diagram of the bracket and cylinder together. The…

A:

Q: 4- For this truss e=60°, a) Determine the type of supports b) Reaction forces at each support c)…

A: Dear student,                     According to the expert guidelines, I am allowed to answer only…

Q: P a 3 a 4 B a 4 а Which of the following is closest to the force in member CD? O a) o O b) -0.707·P…

A:

Q: equilibrium. It is constructed using two-force members, joined at their ends.  I have given you all…

A:

Q: Determine the force of applied, P. such that the system is in static equilibrium. a) P=100N d)…

A:

Q: 500KN 750 KN For the truss shown , the cross-sectional area of each member is 1,200 mm?. 60 60 60 60…

A: NOTE:- As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost…

Q: The sculpture is attached to the wall from a metal rod at A which is a fixed support. The sculpture…

A:

Q: Determine the values of a and b so that the shown beam is in equilibrium when F = 1.5 kN and M = 2.5…

A:

Q: D b C a 60° |A B A) Draw a Free Body Diagram of the post BCD. B) Compute the force at point C. a =…

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.