In reality, both the pressure and temperature increase. If the gauge pressure is 43 atm, what is the temperature of the compressed mixture? (°C) C.

Q: could you pls provide part D and E

A:

Q: How will the date code be applied to the assembly? 2. What paper size is the original version of…

A: Here given engineering drawing sheet shows the PRV Blank assembly drawing which consist of various…

Q: 2. Sharp notches are often added to plastic food packages to help open them (along with arrows…

A: Detailed explanation:Sharp notches are a very good example of the functional features to the plastic…

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: n an engine, the piston diameter is 3 1/4 inches, the stroke is 4 7/8 inches, and the piston…

A: For the solution refer below images.

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: Compare the bolt patterns in shear shown below. The distance from the load to the centroid is the…

A: following is the answer and explanation for the above question-

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: Solidworks. Units are IPS. 24 threads per inch. Primarily just need help designing the threads after…

A: It is asked to draw thread by using Solidworks software

Q: pr... below. 5) Sketch the appropriate sectional view on the front view of the part

A: Given:To find:Sectional view on the front view.

Q: 10 1 R6 1 10 20 50 30 R10 -5 X 45.00° 50 1 1 5 15 5 R30 110 R5 55 20 R6 7 8 60 30 -60 店 06-4 holes…

A: Step 1: First create following top view and extrude it up to required depth i.e. 60 mm

Q: In the moment calculation, why did you take away the h* from 8?

A:

Q: 3.

A: For solution refer below images.

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: A gear train consists of three gears: a pinion (which is the driver), an idler, and a gear (which is…

A: Given:- The gear train of three gears Tidler=68  Tidler(to replace)=37 To find:- Velocity ratio…

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: Define the termTruss?

A: The truss is a structure that is used to distribute the load. It is made by combining members into…

Q: What is the Flexure Formula?

A: The stresses in the beam caused by the bending moment is called as flexural or bending stress.

Q: what is the bottom length?

A: To calculate the bottom length

Q: 15. On the produced part below, show a simple sketch on how the flatness on the part m verified and…

A: Flatness:- It is defined as the minimum distance between two planes within which all the points on…

Q: For the following thread designation, turns, how far have you advanced the O 083 inches O 417 inches…

A:

Q: GER SCALE 9 v 1.3- A 3"-2 ACME .75 1.5 "5 SECTION A-A Ø3.75- D-50 Top and front views of the…

A: Adjusting screw is a screw with threads from 40 to 100 threads per inch. Typically stainless steel…

Q: For each of the mating part pairs below, and lower limit for each part. For A and B, səddn express…

A:

Q: I have three parts that I need answered pertaining to the print provided below.   What material is…

A: To find the material specified for the part in the drawing, refer Title Block of the drawing.

Q: Three blocks A, B, and C and a grooved block D have dimensions a, b, c, and d as follows: a =…

A:

Q: Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has…

A:

Crystalline Imperfections

The crystalline imperfections are described as the geometrical defects in the crystal due to incorrect arrangement of atoms, impurity, vacancy, and many more. It is not possible to achieve a perfect or ideal crystal, practically.