Answered: In order to pull out a nail at B, a…

Name: 4. In order to pull out a nail at B, a force F of 30 lb. is required
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 4. In order to pull out a nail at B, a force F of 30 lb. is required using a hammer. Determinethe components of the force F perpendicular and parallel to the handle of the hammer.305 in.18 in.

Engineering

Mechanical Engineering

In order to pull out a nail at B, a force F of 30 lb. is required using a hammer. Determine the components of the force F perpendicular and parallel to the handle of the hammer. 30 5 in. 18 in.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter3: Resultants Of Force Systems

Section: Chapter Questions

Problem 3.17P: The 3200-1b weight is supported by two cables. Knowing that the resultant of the cable tensions T1...

See similar textbooks

Similar questions

C2X8 X Given the 50 lb. force at point A, replace it by a force acting at B. 6" A
pls help me :( im not too good at this
Determine the value of w and P such that the resultant of the system is a downward force of magnitude 1200 N acting 3.6 m to the right of A. Determine the magnitude of the uniform load w. a.252 N/m b.646.1 N/m c.387.7 N/m d.553.8 N/m
2)The forces and couples shown are applied to two screws as a piece of sheet metal is fastened to a block of wood. Reduce the forces and the couples to an equivalent wrench and determine (a) the resultant force R, (b) the pitch of the wrench, (c) the point where the axis of the wrench intersects the xz-plane. 6 lb-in. 6 lb-in. 15 in. | 11 lb 20 in. 10 lb В (A 12
To detach the lid from a 5-gallon pail, the depicted tool is employed to exert an upward and outward radial force onto the inner bottom rim of the lid. Given that the rim makes contact with the tool at point A and a 20-lb force is exerted on the handle as shown, calculate the force exerted on the rim. FLA WHIT 1.8 in. 14.4 in. A B 3.6 in. $35⁰ 20⁰ 20 lb C
A die is being used to cut threads on a rod. If 18-Ib forces are applied as shown, determine the magnitude F of the equal forces exerted on the 1.000-in. rod by each of the four cutting surfaces so that their external effect on the rod is equivalent to that of the two 18-Ib forces.
Q3) A lug wrench is used to tighten a square-head bolt. If 50-lb forces are applied to the wrench as shown, determine the magnitude F of the equal forces exerted on the four contact points on the 1-in. bolt head so that their external effect on the bolt is equivalent to that of the two 50-lb forces. Assume that the forces are perpendicular to the flats of the bolt head. 1"- A 50 lb A C View C Detail (clearances exaggerated) 14" 50 lb 14"
Determine the force (written as a vector) which BC exerts on member AB (a) if the 820-N load is applied to the center of member AB, and (b) if the 820-N load is applied to the center of member BC.
help
5. Replace the shown by comple and force an equivalent Single force applied to the lever. Determ ine the distance from the shaft to the point of application of this equivalent force. BA 300 mm 300 N 60° 200 N 60 mm 200 N 150 mm'
Resolve the 500-lb of fig. into two components: a shearing component parallel to AB and a normal component perpendicular to AB.
Given 600N