Answered: 1. Replace the loading on the frame by…

1. Replace the loading on the frame by a single resultant force. Specify where its line of action intersects member AB, measured from A. 300 lb 200 lb 400 lb 3 ft- 4 ft B A 2 ft 600 lb-ft 200 lb 7 ft

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.48P: The pole OB is subjected to the 6004b force at B. Determine (a) the rectangular components of the...

See similar textbooks

Related questions

Q: The control lever is subjected to a clockwise couple of 81 N-m exerted by its shaft at A and is…

A: Given data: Force (F) = 230 N Couple at A (M) = 81 N-m (clockwise) a = 165 mm = 22o

Q: 2) Replace the force system acting on the post by a resultant force, and specify where its line of…

A: We have to determine the line of action interests the post AB form point A

Q: Q4'The forces FI, F2, and F3, all of which act on point A of the bracket, are specified in three…

A: The scalar components of a vector are disparities in coordinates, where the origin coordinates are…

Q: Determine the force (written as a vector) which BC exerts on member AB (a) if the 610-N load is…

Q: 300 N Replace the loading on the frame by a single resultant force. Specify where its line of action…

Q: Question 1: (B): Replace the distributed loading by an equivalent resultant force and specify where…

Q: Replace the loading system by an equivalent resultant force and specify where the resultant's line…

Q: Knowing that the two forces shown can be replaced by an equivalent force acting at O (no couple),…

A: If a force F is inclined at an angle θ with the horizontal, then the component of force along the…

Q: AL 90 m 44 m D 11 m B. 45 m 30 m 26 m 21 m 39 m

A: Write the vectors OA and OB.

Q: 300 N 250 N b) Replace the loading on the frame by a single resultant force. Specify where its line…

Q: Q1: The 750 N tension force in cable AB is required to prevent the CA bar from rotating clockwise.…

A: Given Data: The tension in the cable AB is T = 750 N. The configuration diagram can be drawn as,…

Q: A- In Fig.A, Replace the loading system by an equivalent resultant force and specify where the…

A: For the given system of forces To determine Replace the loading by an equivalent resultant force…

Q: 3/2 A carpenter holds a 12-lb 2-in. by 4-in, board as shown. If he exerts vertical forces on the…

Q: Q1\ ABD consists Isosceles triangle. The AB and AD help support pole AC. Known that the tension in…

Q: Determine the height h above the base B at which the resultant of the three forces acts. 270 lb 36"…

A: To determine The height from the base where three forces are acting on it

Q: Q1): The cable stays AB and AD help support pole AC. Knowing that the tension is 120 Ib in AB and 40…

Q: Q2. Replace the force system acting on the frame by an equivalent resultant force and specify where…

A: From the vertical equilibrium of forces, From the horizontal equilibrium of forces,

Q: A couple formed by two 975-N forces is applied to the pulley assembly shown. Determine an equivalent…

Q: 2- Determine the Vertical and Horizontal Component of force at point A and D

A: Option 1 is correct. Ax = 24 kN, Ay = 12 kN, Dx = 18 kN, Dy = 24 kN

Q: The 61-m microwave transmission tower is steadied by three guy cables as shown. Cable AB carries a…

A: First of all we need to find the cartesian force vector acting on point B at the ground. Identify…

Q: Determine the magnitude of the component of the tension force (in kN BD along the designated x-axis.…

Q: Determine the components of all the forces on member ABC of the frame shown. F = l00 N %3D 240 mm…

Q: 3. Determine the resultant force and specify where it acts on the beam measured from A. 9 kN/m 6…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: The distribution of soil loading on the bottom of a building slab is shown. Replace this loading by…

Q: The hydraulic cylinder BC exerts on member AB a force P directed along line BC . Knowing that P must…

A: Given Load P component’s magnitude = 600 N To find The magnitude of the force Component along line…

Q: Replace the three forces acting on the guy wires by a single, equivalent force acting on the…

Q: 1. Determine the resultant force and specify where it acts on the beam measured from A. 2. 9 kN/m 6…

A: A simply supported beam is given It is required to calculate the resultant force and its distance…

Q: 250 N b) Replace the loading on the frame by a single resultant force. Specify where its line of…

Q: The vertical post is secured by three cables. The cables are pretensioned so that the resultant of…

A: Given: The force, F = 120 kN

Q: Determine the height h above the base B at which the resultant of the three forces acts. 26" 635 lb…

Q: Example's Replace the loading system by an equivalent resultant force and specify where the…

Q: Q2. Replace the force system acting on the frame by an equivalent resultant force and specify where…

A: Solution:

Q: acting on the gusset plate of a bridge truss. Show that the resultant force is zero. Example…

Q: Determine the resultant R of the system of distributed loads and locate its line of action with…

A: The net force acting on the beam, Answer: The net resultant on the beam is 1875 lb.

Q: A force F of magnitude 690 lb is applied to point C of the bar AB as shown. Determine both the x-y…

Q: A force F of magnitude 900 lb is applied to point C of the bar AB as shown. Determine both the x-y…

A: Consider the diagram shown below.

Q: 1. Replace the loading by an equivalent resultant force and specify where its line of action…

Q: 3.30 For the truss and loading shown, determine the resultant of the loads and the distance from…

A: For the given truss To determine Resultant of the loads and the distance from point A to its line…

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown,…

Q: Replace the loading on the frame by a single resultant force. Specify where its line of action…

Q: -2.5 ft B 3 ft SUMMARY OF ANSWERS 2 ft 300 Ib R 200 Ib 4 ft 250 lb y

Q: Determine the length b of the triangular load and s position a on the beam such that the equivalent…

A: Calculated the length b of the triangular load.

Q: B) For the simply supported beam shown, replace the distributed load by an equivalent resultant…

Q: Determine the x and y components of each of the forces shown. - 008- Dimensions in mm 800 N 600 424…

Q: Replace the loading by a single resultant force, specify the location of force measured from point…

Q: Q2: Replace the three forces acting on the gear by an equivalent system consisting of a force at O…

A: Consider a force of magnitude 1.2 kN is acting on the location where the force 2.4 kN is acting. If…

Q: Determine the force (written as a vector) which BC exerts on member AB (a) if the 650-N load is…

A: When a push or pull applied on the object in compressible or tensile manner, it has the ability to…

Q: The 83-m microwave transmission tower is steadied by three guy cables as shown. Cable AB carries a…

Q: 2. Replace the loading system by a single force. Specify where the single force crosses the vertical…

Q: 2) Replace the force system acting on the post by a resultant force, and specify where its line of…

A: Apply the equilibrium of forces in the x-direction. Apply the equilibrium of forces in the…

Question

1. Replace the loading on the frame by a single resultant force. Specify where its line of action
intersects member AB, measured from A.
300 lb
200 lb
400 lb
3 ft
4 ft
B
A
2 ft
600 lb-ft
200 lb
7 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Еxample's Replace the loading system by an equivalent resultant force and specify where the resultant's line of action intersects the member measured from A. 200 lb 50 Ib 30 3ft -3 ft -3ft 100 lb
Q.2. Force P is acting in the negative y-direction and has a magnitude of 120 N, and force Q is acting in the negative z-direction and has a magnitude of 225 N. Given this loading, solve for the forces in members AB, BC, EC, ED and AD. A 0.6 m 3 m B 0.6 m 2.25 m 1.2 m 0.75 m
*Take that w1 = 890 lb/ft and w2 = 470 lb/ft .* Pt. A : Replace the loading by an equivalent resultant force and determine its magnitude. Pt. B : Specify the location of FR on the beam, measured from point B.
Fc = 5 kN 3m F = 8 KN F₁ = 6 kN 0.75 m 1. The cylindrical plate is held by the three wires connected at point D. Determine the resultant force.
Determine the forces marked with “x" by using method of section. 50 kN 30 kN- 3 m F 30 kN- 3 m E 30 kN- 3 m A AB -3 m -3 m-
6. Replace the loading acting on the beam by a single resultant force. Specify where the force acts, measured from end A . 700 N 450 N 300 N 30° 60° B. 1500 N-m 4 m 3 m
C2X8 X Given the 50 lb. force at point A, replace it by a force acting at B. 6" A
1. Determine the magnitude and direction with respect to the +x axis on the reaction at A and at C. Note that the body is supported by pin at A and a roller at C. The body's weight is negligible. A 2.4 kN-m 400 40° 200 250- Dimensions in mm -300- B 3 kN
y F3 F2 30 F1 Q3- Resolve each of the forces F1 = 10 kN, F2 = 18 kN and F3 = 12 kN, into components acting along the x and y directions and determine the following: (a) The magnitude of FR is . kN (b) The direction of FR measured from the x-axis is (degrees) ..........
Use the rectangular component method to solve the fol- lowing problems. Determine the magnitude R of the re- sultant of the forces and the angle 6, between the line of action of the resultant and the x-axis for F2= 900 b F3= 750 lb F, - 1200 Ib 20 30 F4 = 520 lb 12
with the following modifications: Replace the vertical 6kN at point B with a horizontal force 6kN acting to the right at the same point.
The beam is subjected to the two forces shown. Determine the magnitude of the resultant force. F2 = 250 lb 60° 135 60° 24- 25 |F, = 630 lb Select one: O a. 200 lb O b. 300 lb O c. 500 lb O d. 400 Ib