In order to evaluate the properties of a material, samples are taken and tested.What are the two most important factors that must be satisfied when the sample is collected? Show how these factors can be satisfied.

In order to evaluate the properties of a material, samples are taken and tested.What are the two most important factors that must be satisfied when the sample is collected? Show how these factors can be satisfied.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. Determine the modulus of elasticity for this material: ____x106 lb/in2. Pay attention to units and calculate your answer to 1 decimal place for the unit specified above.
The rectangular metal block shown in Figure is subjected to tension within the elastic range. The increase in the length of a is 0.05 mm and the Poisson’s ratio for the material is 0.33. If the original lengths of a and b were 50 mm and 25 mm, respectively, what is the change in the length of b? Is this change expansion or contraction?
A specimen is originally lft long, has a diameter of 0.5in, and is subjected to a force of 5001b. When the force is increased from 5001b to 1,8001b, the specimen elongates 0.009in. Determine the modulus of elasticity (2 decimal places in 103 ksi) for the material if it remains linear elastic.
A spherical ball of volume 20 m³ is placed under a certain liquid wherein the ball is subjected to a uniform hydrostatic pressure of 200 MPa. If the material of the ball has a bulk modulus of elasticity of 2.5 x 10 x 105 MPa and a Poisson's ratio of 0.30, then due to the hydrostatic pressure, the volume of the ball will change by (1. m3
Please answer both
QUIZ · Example I: Given the following state of stress and material properties Ox = 10MPa E = 200GPA Tyx 0z = -15MPA v =0.2 Tyz = 5MPA · Determine the state of strain - Determine the change in volume (also known as volumetric strain or dilatation)
6.What is elastic deformation? Plot the load-deformation curve for an elastic material schematically under loading and unloading on the graph below.
Measurements should be reported to the nearest 1000, 100, 10, 1, 0.1, 0.01, 0.001 units, etc., depending on their variability and intended use. Using your best judgment, how should the following measurements be reported? Deformation of a steel specimen during the tension test (in.) Tensile strength of steel (psi) Modulus of elasticity of aluminum (MPa) Weight of aggregate in a sieve analysis test (grams) Compressive strength of portland cement concrete (psi) Moisture content in a concrete masonry unit (percent) Asphalt content in hot-mix asphalt (percent) Specific gravity of wood Distance between New York City and Los Angeles (miles) Dimensions of a computer microchip (mm)
Using the Stress-Strain diagram for polymers below, identify the types of polymers depicted based on their Stress-Strain behavior/curve 60 A 50 40 30 В 20 C 10 1 2 4 5 6 7 8 Strain A. [ Choose ] B [ Choose ] [ Choose ] > 3. Stress (MPa)
An aluminium alloy bar of circular cross section as shown on the figure is loaded by tensile forces, P. The length and diameter of the bar are 3.0m and 30mm, respectively. If the bar elongates by 7.5 mm, what is the decrease in diameter Ad? What is the magnitude of the load P? Its modulus of clasticity E=73 GPa and Poisson’s ratio=1/3. (
Please annotate the attached image to highlight the different phases of a polymer stress/strain graph. From the attached graph, calculate the following: 1-modulus of elasticity 2-tensile strength 3-the ductility in % of elongation 4- yield strength at a strain offset of 0.002
How and Why is the Hardness of Mineral important in Civil Engineering? Provide a thorough discussion