In line with the correct answr to the previous question, indicate which statements are true about fractional distillation. Select all that apply. The most efficient fractional distillation should have as many vaporization- condensation cycles, also known as theoretical plates as possible. The most efficient fractional distillation should have one vaporization- condensation cycle, also known as theoretical plate. The most efficient fractional distillation should have the longest fractionation column, which would allow for as high a number of theoretical plates as possible. The most efficient fractional distillation should have the shortest fractionation column, which would allow for as low a number of theoretical plates as possible. The longest fractionation column also has the highest column holdup and the lowest column throughput. The longest fractionation column also has the highest column holdup and the highest column throughput.

In line with the correct answr to the previous question, indicate which statements are true about fractional distillation. Select all that apply. The most efficient fractional distillation should have as many vaporization- condensation cycles, also known as theoretical plates as possible. The most efficient fractional distillation should have one vaporization- condensation cycle, also known as theoretical plate. The most efficient fractional distillation should have the longest fractionation column, which would allow for as high a number of theoretical plates as possible. The most efficient fractional distillation should have the shortest fractionation column, which would allow for as low a number of theoretical plates as possible. The longest fractionation column also has the highest column holdup and the lowest column throughput. The longest fractionation column also has the highest column holdup and the highest column throughput.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Q2/A mixture of A and B is to be separated by distillation Xf=0.45, concentration of distillate is 0.92 and waste is 0.05, the Reflex ratio is 2. find No. of trays of the distillation columns if equilibrium line is noted as in the figure and the feed enters the column at boiling point. 1.00 0.8 0.6 0.4 0.2 0.6 0.8 1.0 XA YA 0248 11 0,4
[2] A mixture containing 70 mol% n-heptane and 30 mol% n-octane is subjected to a batch distillation at 1 atm pressure. What will be the composition of the distillate after the first 25 mol% of the original charge is distilled. Estimate the initial and final boiling point and what is the composition of the first vapor condensed? T-x-y values of n-heptane 106 0.647 T. "C 98.4 100 103 110 115 120 122 124 125.6 1 0.922 0.776 0.495 0.318 0.156 0.097 0.039 1 0.963 0.883 0.801 0.681 0.500 0.281 0.184 0.078
Which of the following consideration are applied when choosing a suitable recrystallization solvent? (TRUE / FALSE) True False Should have a boiling point that is ~ 30-40 ℃ above room temperature. True False Dissolve the compound in a reasonable amount of solvent. True False Should be unreactive toward the compound of interest. True False Offers moderate solubility of the compound to be purified at room and lower temperatures. True False Does not dissolve impurity at all or complete/high solubility of impurity at all temperatures.
1a. Use the given table to construct a temperature-composition diagram for cyclohexane Toluene mixture. Based on the plot, what is the composition of the distillate obtained by Simple distillation 20 mole percent cyclohexene and 80 mole percent toluene? Show your Work on the plot. 1b. Estimate the composition of the distillate of 20 mole percent of cyclohexane if the Distillation column had three theoretical plates.
Two liquids, A and B, are mixed. The mole fraction of B for this mixture is 0.65. This mixture is purified through fractional distillation. What will be the temperature of the vapors as liquid begins to be collected from the distillation column? The following information may be useful. Boiling point of A: 85 "C Boiling point of C: 157 "C Boiling point when XB = 0.65: 125 °C Select one: a. 85 °C b. 157 "C c. 125 "C
Fill in the blanks: a) The component of the mixture that becomes a water soluble salt by treating the two component mixture with sodium hydroxide solution has the highest _______________. b) The lower phase in equipment used for liquid-liquid extraction in a water-dichloromethane mixture is_____________, because _______________. c) The component of the mixture that becomes a water-soluble salt is the one with the greatest ______________
Show all working explaining detailly each step Answer should be typewritten using a computer keyboard!
Florence is only able to find 0.015 M aqueous KI/I2 on the reagent cart, so they perform a dilution by combining 10 mL of water and 10 mL of the available reagent. They now have 0.0075 M aqueous KI/I2 which can be used at station C. Is there a difference in the chemical composition of the solution Florence made from what was available on the reagent cart? Group of answer choices no, because water was already present in the solution yes, because water was added to the solution
Based on the melting point of your impure solid, you look at the given samples and believe you havecompound A. Compound A is recrystallized using a mixed solvent system of ethanol and water. You add1 ml of hot ethanol to your sample and it doesn’t completely dissolve. You continue to add hot ethanolbut there isn’t any change. Some solid remains. What should you do next?
MAKE A METHODOLOGY : MATERIALS/ REAGENTS WITH SCHEMATIC DIAGRAM . THE PICTURE UPLOADED SERVES AS A GUIDE, DO THE SAME THING BASED FROM THE PIC. Procedure: Place 20 drops of each of 0.2M CuSO4 in a centrifuge tube. Then add 5 drops of freshly prepared 6M (NH4)2S to each centrifuge tube. Record your observation. Centrifuge the mixtures for 3 mins. and decant the supernatant liquid. Add 10 drops of DI water and 10 drops of 6M HNO3. Stir and boil the mixture in a hot water bath for 5 mins. centrifuge the mixture for 3 mins. Decant the supernatant solution from procedure 3. Discard the To each of the supernatant liquid, add 6 drops of 6M H2SO4. Allow themixtures to cool and 5 drops of DI water. To the mixtures in procedure 4, add few drops of concentrated NH3 until the solution becomes basic. Confirm using a litmus paper. Record your observation. Add 1 drop of 5M NaOH and 1 drop of 0.1 M SnCl2 to the centrifuge tube containing Bi3+ ion , centrifuge and decant the supernatant liquid. To…
10. if a 75%hexane /25% ethyl acetate mixture is used as a solvent system and the sample of interest does not move from the origin, describe how the solvent should be changed
3. In the liquid-liquid extraction, there are two funnels with solutions of total volume 250 mL and 500 mL respectively. Using the ratio of 1 part of aqueous to 3 parts of ethyl acetate for liquid-liquid extraction, how much of ethyl acetate is needed for each funnel?