In free space, V = 6xy2z + 8. py at At point P (-2, 2, 2) %3D O 954.9 pC/m3 o 1697.65 pC/m³ O 106.1 pC/m3 O 424.4 pC/m3

Q: Hi there, this question is for control systems. Could I get help in completing it? Thanks.

A: 1. The differential equation that I find fascinating is: dt2d2y​+2dtdy​+2y=u 2. In this equation,…

Q: The response of zero order instruments is faster than first order instruments. True False

A: Yes, zero order is more faster than 1st order. Because there is no dynamic delay.

Q: (s) G₁ H₁ G₂ Hy G3 H₂ G₁ C(s)

A:

Q: Solve the following differential equation subject to the specified initial conditions. d²i +5+41 = 8…

A:

Q: 10-ohm resistor and 10 H inductor are connected in series across a source of 12 V. If the current is…

A:

Q: The circuit diagram is shown as below. ↑ is R₁ Vc C L iz 1. Find the input-output differential…

A:

Q: 2. Model in state space the following circuit consider the first state the voltage in the capacitor…

A:

Q: Figure below shows a series RL circuit with an applied voltage, Obtain a differential equation…

A:

Q: Please now solve p2 of this question

A: we need to answer above question.

Q: Q2 Show that any signal can be decomposed into an even and an odd component. Is the decomposition…

A:

Q: Generate differential equations,of the electrical circuit by hand using Newton’slaw and the basic…

A:

Q: Which of the following is not a characteristic of the N-R method? All of these Convergence is…

A: we will list some important characteristics of newton raphson method to choose the correct option.

Q: Design a value for R,, R, and Rcs such that 0.5 mA can be delivered to loads up to 18k

A:

Q: 1. Add the following numbers that are in 2's complement (n=7). Show your work, and convert all…

A:

Q: Show that the LRC circuit given below can be described by the differential equation L d²i + R di + 1…

A:

Q: 3. An electrical fan is used to cool electrical components when the temperature exceeds a certain…

A: As, we calculated before, IC=1.01 Ampas we know the ratio of IC to IB=26ICIB=261.01IB=26IB=0.39 Amp

Q: Assume the OPAMP is ideal. For the circuit shown below: R=0.3k, C=0.201nF, L=5.6mH and the voltage…

A: The Amplifier circuit is given as Here opamps are configured as a voltage buffer. So, the output…

Q: mplify the block diagram shown in following figure and obtain the closed-loop ansfer function…

A: The solution is given below

Q: What's the damping ratio zeta for this system with its closed-loop poles as shown? jo 14 j2 -6 -2 to…

A:

Q: P(t) 9(t) -4 -2 2

A:

Q: Problem 2 Define the initial current , the final current ly, the time constant r, and the current i…

A:

Q: Q3 Develop the transfer function from the following block diagram form Figure Q3: H2 R(s) G1 G2 G3…

A:

Q: Calculate the value of R needed to have a critically damped response. 0.01 F 0.01 F 16 R www 4 H m 4…

A:

Q: R(s) Answer: T(S) G1(s) G₂(s) G3(s) G4(s) G5(s) G7(s) G6(s) C(s) G6 G4+G6G3+G6 G5 G3 + G6 G5 G₂…

A: Given Data:A block diagram model with,Input Output To Find:The transfer function.

Q: a) Find the time cnstant of the crcult t=? b) The total Chorge in the capacitor system half of the…

A: To solve above question, one should understand the behavior of Inductor and capacitor in DC circuit.…

Q: A=s³+5s²+5s+2+K=0

A:

Q: Astable multivibrator was designed using a 555 timer. The periodic time of the output signal should…

A: An astable multivibrator, also known as a free-running multivibrator, is a type of oscillator…

Q: Find the transfer function from force u to posi- tion y y k F m₂ Y( w m₂ u Frictionless surface

A: Given that ,                                                           Transfer function

Q: Explain what happens due to the shadow effect when solar PV panels are connected in series?

A: we need to explain what happens due to Shadow effect when solar PV panels are connected in series.

Q: b) Solve the given two numbers using BCD addition. (C5) ,„ + (B2) „ =(?),D 16 16

A: Given, C516+B216=?BCD

Q: Q1 (a) The signals p(t) and q(t) are shown in Figure Q1(a). P(t) q(t) 4 2 -2 -2 2 4 Figure Q1(a)…

A:

Q: C1 R1 R2 Vin (t) Vout (t) C2 Figure Q1 Consider the circuit shown in Figure Q1. A voltage input…

A: In the above circuit firstly we will take laplace transform of the circuit and then use voltage…

Q: Given the following state equations and the output equation a. b. x=-x₁ + 2x₂ + u x₂ =-3x, x₂ + Su…

A:

Q: Problem 1: For T = 0.3 sec, write the element of the discrete sequence corresponding to the function…

A: Given data: The function, ft=t3 k=39 T=0.3 sec

Q: Q2:Solve the following using 2's complement representaion method. (a) 1010100 - 1000100 (b) 1011100-…

A: Given: (a) 1010100-10001002's compliment of 1000100 = 0111011+1…

Q: estion 6 The values of determines whether the response is overdamped, underdamped or critically…

A: The value of  DAMPING RATIO ( zeta )  determines whether the response is over damped , under damped…

Gradient of a Scalar Field

Consider a room or a place where the temperature is denoted by a scalar field T, such that at each point (x, y, z), the temperature is given as T(x, y, z). It is independent of time, in which the temperature rises most quickly. The gradient of T will show the direction at that point by moving away from (x, y, z). How far will the rise in temperature in that direction be determined by the gradient magnitude? Consider a surface that has a height above sea level at point (x, y) which is given by H(x, y). At that point, pointing in the direction of the steepest slope or grade is the gradient of H. The magnitude of the gradient of the vector gives the steepness of the slope at that point. How a scalar field changes in another direction can be measured by the gradient by taking a dot product rather than just the direction of the greatest change?