In figure below, The potential across the resistor is equal to: L 650 mH 120 V 60 Hz R472 :1pF

Q: Using KCL, find the unknown currents. 3.5 mA 8 mA $1

A: To find out unknown currents in the diagram given, Given Iout = 8 mA

Q: What is the totel current? R1 R3 RS 3 kOhm V1 111 V 2 kOhm 1 kOhm R28 kOhm R47 kOhm R66 kOhm

A:

Q: 3. Determine the total resistance and the total current. 100V 1 + 1002 M 15.2. M 1502 500 1052 1022

A:

Q: Given the following Resistances and Capacitors in Series and Voltage Source: R1 = 9 ohms R2 = 5 ohms…

A:

Q: 2A R1 R2 100 R3 R4 12V Figure 7

A:

Q: 150 Vm sin'do x3 vm.s 30

A:

Q: 6V RI 2.39 R3 6.0goA 5 V find the ćurrenes of thestdy?

A: Let us assume I1,I2 and I3 be currents in each ammeter and i1,i2 qnd  i3 be currents in each…

Q: AU Resistanceo =2n Find the exforosion $ equivalene sita thevalye op equial %3D R2 9. Ry reistanu

A: We are authorized to answer one question at a time, since you have not mentioned which one you are…

Q: (i) Analyse comparator circuit (op-amp U1) and compute its output voltage Vo1 sampled by probe PR2.…

A: "According to the Company's policy we will solve first three subparts of the question". Given the…

Q: What is the current lo in the figure if Is = 70? Is 2 A

A: Given :  Note : Please note that according to the units of the other currents we have assumed the…

Q: 12V 2012 4052 * 50Ω www – 10Ω 30Ω

A:

Q: Determine i, and iz in the figure i2 10 V 10 N 3 V

A: To find the currents i1 and i2

Q: The equivalent resistance between points a and b in the figure is 5.000 ww 10.00 5,000 W 4.00 W…

A:

Q: 2r (a) -Q -2Q (b) D- D- 2r 5- r (c) (d) What is correct order of the charge systems fr c>a>d>b A)

A: Here is the answer

Q: Question 1 A direct current (DC) of 4A flows into a previously uncharged 20 uF capacitor for 3 ms.…

A: For the given data voltage between the plates are determined as shown below

Q: Three resistance 14. 5 Q, 25.5 Q and 60 Q are connected in series across 200 V. What will be the…

A: Given: Three resistances are connected in series, R1=14.5 ΩR2=25.5 ΩR3=60 Ω Supply voltage, Vs = 200…

Q: Question 1 What would be the maximum current through the resistor? Express your answer in amperes…

A: As per the guidelines of Bartleby we suppose to answer first three subpart only for solution of…

Q: 10 0 45 Q 25 Ω L00 V 20 Q ww

A:

Q: Determine the values of resistance R and inductance L. need help on question C ，urgent

A: Solution (c) -  The circuit diagram is shown below,

Q: Determine Rin (in MQ) for the figure. Ipss= 10 mA Vp=-4 V 4.7 kN 10 V o Mw Mw0-2.5 V 2 MN

A: The given circuit is shown below: VGG=-2.5 V VDD=10 V RD=4.7kohm RG=2Mohm

Q: May you explain part b a bit more I'm confused about how you got 2.5 after sin and e-j2.5

A: The problem has been solved below

Q: Figure 5 shows a current series feedback amplifier. The sampled current signal is the output…

A:

Q: Q6/ What is the dc source voltage? 0.013 R1 kOhm R232 kohm R323 kohm 78 V 39 V 13 V

A:

Q: 7. Determine all of the resistor values in figure below. if RT = 7730. 15.53 mA R₁ 3.64 mA R₂ ww +1₁…

A: Given Circuit:Total resistance, To determine:Value of resistances

Q: Given the following Resistances and Capacitors in Series and Voltage Source: R1 - 7 ohms R2 = 4 ohms…

A: According to the question we have to find the value of the amplitude of the voltage across C1.

Q: How much resistance must be inserted in series with a 0.96-H inductance to limit the current to 0.25…

A: To solve above problem, one should have basic idea about working of AC circuits. Above given circuit…

Q: The potential difference is measured in .volt

A: Potential Difference:

Q: Determine Rin (in MQ) in the figure. 9 12 V Rp2 kQ RG C2 10 MQ 1 µF D ID(on) = 6 mA VGs (on) = 8 V G…

A: The circuit diagram is shown below, Here,ID=6mAVGS=8V=3V

Q: The voltage divider shown in the figure has a potential difference (V) between point A and B and a…

A: The circuit diagram,

Q: 12/V www A. 10 ohm www B: 40hm ww F: 0.1ohm www D: 20hm WWW E: 1 Ohm

A:

Q: Current I in the figure is 2A 1A 2A 1A SA 1A 1A O 3 A O4 A O 5A O6A

A: We need to calculate current I for given network ,we will use krichoff's current law .

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.