What is the voltage at the resistor and capacitor?

Q: D2.2 and find E

A: Given:  QA=-0.3 μC at rA=25,-30,15,QB=-0.5 μC at rB=-10,8,12

Q: Determine the branch currents 12V 79 + LETTERING 9Ω 10V 6Ω 992 NCH MA 15V

A:

Q: Q6 Given three signals x1(t), X2(t), and x3(t) whose frequency contents are shown. These are given…

A:

Q: 3 (b) Determine whether or not each of the signal is periodic. If a signal is periodic, determine…

A: A signal x(t) is said to be periodic if it repeats itself after finite amount of time 'T' and that…

Q: Find Fan-in of the circuit. Fan-out of the circuit.

A:

Q: &€ R3 M 2₁ R²₂ R₁₂ R4 R3 M M R4 R₁ R₁ = 452 1₂ = 652 R3 = 222 R4₁ = 822 R₂ R3 R₁ R₁ ww R4 WR4 M W R₁…

A:

Q: WAVEFORM. DH 47 k V

A: Here we have to draw the output waveform.

Q: What is the value of It. V1 100V It-Blank 1 A Blank 1 R1 100Ω Add your answer C1 €0.001FF

A: Given that: The circuit is shown below. Find the value of i(t).

Q: vt CALCULATE V. FOR THE CIRCUIT BELOW AND SKETCH THE OUTPUTT HAUFFORM t t Vin D DH 22.0kn SV V6

A:

Q: (a) A piezoelectric crystal is characterized by a constant, 12 x 10-13 (V/m) / (N/m2). The diameter…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 2- F(A, B, C, D)=(2, 11, 12, 13, 14, 15). Design circuit for this minterms by using 3x8 MUX.

A:

Q: 37. Sketch v, for each network of F'ig. 2.181 for the input shown. 20 V + Ideal -20 V (a) FIG. 2.181…

A:

Q: 1. What is the difference between synchronous binary counter and asynchronous binary counter? 2.…

A: 1. On the basis of applied clock speed, counters are of two types: Synchronous Counter  Asynchronous…

Q: 12V σ 10 ΚΩ Fig. B lp. 5 ΚΩ Si ora

A: SOLUTION           From the given circuit diagram         BY KVL FROM…

Q: Solve the following problem in detail:

A: Write the expression for frequency deviation as follows:

Q: 8. ± √36 = 16 V25 9. 10. + 169 V256

A:

Q: 1.) R,= 120 A R,= 180 2 R, = 120 2 R, = 360 n R5 = 200 N V R= 100 2 120 V ww R3 = 60 2 R, = 180 2

A:

Q: For the given circuit what is the value of X(s). V1 100V R1 1000 C1 0.001FF

A:

Q: solve with complete solution

A: Given: A block diagram,  To find: a) System function and zero state step response for a=0.5, b)…

Q: +15 V Si V₁ 10 ΚΩ ID. Ge Voz

A:

Q: 4. Draw 3-bit synchronous counter and write its truth table?

A: We need to design 3 bit synchronous counter . We will Design the 3 bit up counter by using of T flip…

Q: 7.16 Use the step-by-step technique to find i,(t) for t > 0 in the network in Fig. P7.16. 2 kN 4 k2…

A:

Q: 7.14 The value of V, in the circuit in Fig. P7.14 is 20 V for t 0. Find i,(t) for t 0. X.

A: As per bartleby guidelines for more than one question asked only one has to be answered. Please…

Q: 3. Use nodal analysis to solve the circuits below. a Ix 620°v 2Vx 10 be I2 -jin 21x jia 12 Vx ell

A: In this question,  We need to determine the current using the  nodal analysis.

Q: Q2 Given R=100KN, C = lµF, input is V,(t)and output is V.(t) a. Find the differential equation…

A:

Q: Assume that the switch in the circuit of Fig. P7.51 has been in position a for a long time and that…

A: a Before shifting switch from a to b Vc(0-)=vc(0+) =-50V

Q: Determine the branch currents using Kirchhoff's Laws. R1 = 20 R2 20 R3 = 2 0 R5 = 20 20 100 V R6 =…

A: Current through branches solved by using KVL

Q: 22. A single phase halfwave controlled rectifier has 400 sin 314 t as the input voltage and R as the…

A:

Q: 7.21 In the network in Fig. P7.21, initial values are i,(0) = 20 mA and iz(0) At what time is v(t) =…

A: As per bartleby expert policy, only 7.21 individual question is to be answered. Kindly repost 7.24…

Q: Q3 List down properties, find transfer function, frequency response, impulse response and output for…

A:

Q: 47. For the circuit depicted in Fig. 10.58, (a) redraw with appropriate phasors and impedances…

A: KCL states that algebraic sum of current at a node must be equal to zero. This is also called nodal…

Q: 1. An ideal transformer with N = 2400 and N2 = 400 is connected with an impedance Z2 across winding…

A:

Q: 3. Determine Vo using mesh analysis. 20V 45 V 1502 M Il 82 + F% + 14 1022 12 3222 M 13 2012 +48V

A:

Q: Consider the amplifier shown below. Transconductance of M₁ is gm and there is no channel-length…

A:

Q: 1. What is D-latch? What is its purpose? Draw its combinational gates and write its truth table?

A: Latch is an electronic device. This device is mostly used to store 1 bit memory data. The D latch is…

HVDC

HVDC stands for high voltage direct current in the electric power transmission system. The high voltage direct current system uses direct current (DC) for the transmission of electrical power through transmission lines in contrast with the alternating current that is the AC system. The HVDC is used to transmit bulk power point-to-point through long distances transmission lines. Power is rapidly transferred because the efficiency of transmission lines is greatly increased over long distances due to HVDC lines.