In Figure below all fluids are at 2o deg.C. Determine pressure at point B, if pressure at point A is 150 kPa and weight of air is neglected. Use the table below for the densities at 20 deg.C. Liquid P. kg/m Kerosene - Ammonia 608 Benzene Carbon tetrachloride 881 Air 1590 Benzene Ethanol 789 1117 Ethylene glycol Freon 12 Gasoline 40 cm 19 cm 1327 680 20 cm 8 14 cm Glycerin Kerosene 1260 cm 804 13,550 791 Mercury- Water Mercury Methanol SAE 10W oil 870 SAE 10W30 oil SAE 30W oil SAE 50W oil Water 876 891 902 998 Seawater (30%o) 1025

Q: steel structure

A: Steel structures are widely used in modern construction due to their strength, durability, and…

Q: What is section modulus?

A: The section modulus helps to calculate the outermost stress in the beam section. It is numerically…

Q: A metal disc of 20mm diameter is to be punched from a sheet of 2mm thickness. The punch and the…

A: Given operation is blanking operation. Blank operation  = D = 20 mm Sheet thickness = t = 2mm…

Q: Write short note on compression ratio

A: compression ratio

Q: Identify the material handling equipment   used for handling heavy casting in  foundry  Platform…

A: Bridge crane also known as overhead cranes are commonly used in the foundry industry to lift heavy…

Q: I need the answer for problem number 14.

A: 14.In this drawing, only one chamfer is represented by the leader line. The chamfer is represented…

Q: List four sources of engineering failures

A:

Q: State two reasons copper pipe is becoming more popular for fire protection systems

A: Almost all fire protection systems use carbon steel, but the use of copper in fire protection…

Q: Flow can be increased by increasing perforation? 1- Yes 2- No

A: What is perforation and how this affect the flow

Q: Q13: is Safety device that -- works on the principle that two dissimilar metals with unequal…

A: Temperature device

Q: 3. F= 160,000 lbs. GRAY CAST IRON 1.25 1.00 0.25 50 1.00 F = F= 160,000 lbs. 7.25 ult A= 1000 6=…

A:

Q: machine design 1 question welding check the seam safety Example= Vd. ME Given data

A: For the given material specification, the yield and tensile stress.

Q: How pilot tube works?

A: The pitot tube is a simple device that is used to measure the flow velocity with no moving parts.

Q: 2. Comparison between; a. Bar/Rod & Beam b. Tube & Pipe

A: a) Rod & Beam Comparison 1) Rod usually has circular cross-section.  1) Beam may has different…

Q: Removable joints can be made by using welding. Select one:

A: This statement is (FALSE)

Q: List any four factors that are to be considered in selection of storage tanks?

A: The factors are listed below:

Q: The general specification for production tubing is

A: After the casing has been run and cemented in place, production tubing is run into the drilled…

Q: Filler rod material is same base metal used in gas welding process. Select one: True False

A: Above statement is true.

Q: On the part attached, what is the flatness on the top surface with only the profile applied? And…

A: from the given the top surface flatness must be within  0.4 tolerance zone with respect to bottom…

Q: Generally, the Poisson's ratio of steel is

A: Poisson ratio of steel = 0.3 Option (c) is correct.

Q: 110 About indistrial piping WHY IS THE ASME 31.3 ALLOWABLE STRESS A COMBINED STRESS?

A: The objective of the question is to understand why the ASME 31.3 allowable stress is a combined…

Q: 4. (Ef-1 X¡)^2 =D1

A: Sigma indicates sum of ^ indicates power.   In order to solve this, the following equation should be…

Q: Comparision between pulverized coal firing and stoker firing.

A: Pulverized coal firing and stoker firing are two common methods used for combustion in boilers to…

Q: What is the maximum gas flow rate for a nozzle size?

A: GIVEN; What is the maximum gas flow rate for a nozzle size?

Q: How is done evaluation of whether the improvement is useful and which side of the pipe should be…

A: In order to choose the best strategy, it is necessary to weigh a number of aspects while assessing…

Q: Which of the following statements pertaining to the steel tubing is not true: Steel tubes are…

A: Given: Steel tubes are better than steel pipes because, they:   are less expensive.…

Q: The wall thickness of a pipe is referred to as the pipe's __________.

A: Thickness of the pipe is nothing but the difference between outer radius and inner radius.

Q: Provide any six types of flanges used in piping.

A: Here are six common types of flanges used in piping systems:Weld Neck Flange: Characterized by a…

Q: A circular duct is to measure 20.5 centimeters in diameter and 75 centimeterslong. It has a butt…

A: Given Data  Circular diameter of the duct, D=20.5 cm The radius of the duct, r=d/2=20.5/2=10.25cm…

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: The term, Orthogonal, describes the relationship of the axis of the ½” NPT pipe plug with the main…

Q: Give all the parts of a simple vertical fire tube boiler

A:

Q: A wood box beam is constructed of two 260 [mm] x 50 [mm] boards and two 260 [mm] x 25 [mm] boards…

A: According to the information we have, Two 260x 50 panels and two 260 x 25 panels are constructed…

Q: Maximum Stresses in Thick Walled Cylinders

A: To determine the maximum radial and tangential stress for the thick walled cylinder

Q: What is the ideal column?

A: An ideal column is one that is perfectly straight, made of a homogeneous material, and free from…

Q: 57. In gas welding process, rubber is used as preferred material for hoses. Select one: True False

A:

Q: advantage and disadvantages of using STRAIN GAUGE

A: Given: Advantage and Disadvantages of using STRAIN GAUGE

Q: Process Flow Diagram of Mechanical Draft Cooling Tower

A: In mechanical draft cooling tower, the air is moved by power-driven fan motors to force it to go…

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.