In combustion engines oil is used for lubrication. The oil enters the oil cooler while its temperature is still high. Inside the oil cooler, the oil will move around the pipes that are fitted with fins that release heat. Once the oil is processed, it will leave the cooler at a temperature that is cooler. This cycle continued repeatedly. You are given that unused engine oil exiting the engine block at 60°C flows over a flat long plate which has length of 5 m which is the oil cooler for a combustion engine. The plate temperature is 20°C and the oil flows with velocity of 2 m/s. You are required to calculate: 1) Total drag force, (ii) The rate of heat transfer per unit width of the entire plate. You are given that the critical Reynolds number is 5x10°. oil T-= 60°C V-=2 m/s T-20°C L= 5 m

In combustion engines oil is used for lubrication. The oil enters the oil cooler while its temperature is still high. Inside the oil cooler, the oil will move around the pipes that are fitted with fins that release heat. Once the oil is processed, it will leave the cooler at a temperature that is cooler. This cycle continued repeatedly. You are given that unused engine oil exiting the engine block at 60°C flows over a flat long plate which has length of 5 m which is the oil cooler for a combustion engine. The plate temperature is 20°C and the oil flows with velocity of 2 m/s. You are required to calculate: 1) Total drag force, (ii) The rate of heat transfer per unit width of the entire plate. You are given that the critical Reynolds number is 5x10°. oil T-= 60°C V-=2 m/s T-20°C L= 5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A circular pipe with inner diameter of 0.02 m has its inner surface covered with water at 300K. Dry air is flowing inside the pipe at the velocity of 0.8 m/s. The temperature of air is 300K and its pressure is at 1 atm. Calculate: a) Mass transfer from the 0.01 m length pipe b) Rate of heat transfer from pipe to air by mass convection and heat convection
An electric heater heats the inner tube walls of a concentric tube annulus at a rate of 2000 W/m. The inner and outer tube diameters are 25 and 50 mm respectively. Water enters the annular region at 25 ⁰C and leaves at 85 ⁰C. The flow rate of water is 0.04 kg/s and the outer tube wall is insulated. Assuming that fully developed conditions exist at the outlet, the inner tube surface temperature at the outlet will be ?
A shell-and-tube heat exchanger is used to cool compressed liquid methanol from 176 °F to 104 °F. The methanol flows on the shell side of the exchanger. The coolant is water that rises in temperature from 50 °F to 86 °F and flows within the tubes at a rate of 68.9 kg s1. Finding the appropriate thermophysical data and applying the proper equations, you are required to do the following: (a) Calculate i) methanol mass flow rate in the exchanger, ii) methanol volumetric flowrate at the inlet of the exchanger. (b) i) For the counter-current flow of the fluids calculate the log temperature difference, ii) explain the purpose of calculating this difference, iii) explain, quantitatively, why is the counter-current flow in heat exchangers preferred to co-current flow. mean
a one shell and two tube pass heat exchanger, coolant enters the tube at 4.81 kg/s (spread over 72 tubes with each tube being 0.01 m in diameter and 1.95 m length) at an initial temperature of 25 C. Water enters the shell at 2.5 kg/s at an initial temperature of 5 C. The average convection coefficient of the water is known to be 1e4 W/m2.K. What is the overall heat transfer coefficient, assuming no fouling, negligible tube thermal resistance and near-identical inner and outer tube surfaces? What is the actual heat transfer rate? What is the coolant outlet temperature? The coolant properties are Cp = 1040 J/kg.K, μ = 7.65e-4 kg/s.m, k = 0.058 W/m.K and Pr = 14. Assume the water Cp = 4200 J/kg.K.
Hello Sir,Good Afternoon. I have a question in my homework related Heat Transfer lesson. The following below is my question. Please Advice. Thank You
A condenser consists of 5 pieces of 3 m long 1/4 in Sch 40 horizontal pipes lined up in 6 rows. It transfers cooling water with a heat transfer coefficient of 2000 W / m-K through the pipes. As the flow rate of the water is very high, the water temperature is constant at 35 degrees Celsius. Saturated heat vapor condenses at a pressure of 2 bars outside the pipes. Calculate the condenser capacity in kW
Consider the flow of motor oil (cp=2048 J/kg K) through a copper tube ofthin wall at a rate of 0.3 kg/s. The oil enters the copper tubes at atemperature of 80°C that is cooled by means of water that enters at 20°C. Temperatureoutlet of the oil cannot be higher than 40°C. The convective coefficient ofheat transfer from the oil side is 750W/m2 K and from the water side 350W/m2 K. IfThe outlet temperature of the water is measured at 32°C and a heat exchanger is considered.double tube in parallel. Determine: a) Mass flow rate of the water. b) The difference of log mean temperatures. c) the area of the heat exchanger.
Q) Compare the heat transfer coefficients under the following conditions (Assume flow is turbulent). (1) Two fold increase in the diameter of the tube; the flow velocity is maintained constant by a change in the rate of liquid flow. (2) Two fold increase in the flow velocity by varying the mass flow rate. Comment on. the results.
Q-2/ An office room has an area of 7*5 square meter and 4m height, this room is heated by the radiator of a steam-heating system. The steam radiator transfers heat at a rate of 10 MJ/h, while a 100-W fan is used to distribute the warm air in the room. During this process, the rate of heat loss from the room is estimated to be about 5 MJ/h. If the initial temperature of the room air is 15°C. Determine; how long it will take for the air temperature to rise to 25°C. Assume constant specific heats at room temperature and the parametric pressure is I bar.
Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1592 kJ is supplied to saline water in the steam generator to heat from 26ºC to 119ºC for the generation of water vapor, Take the density & specific heat of the solution as 1030 kg/m3 & 3.2 J/kgºK respectively. Solution: Change in Temperature (in K) Answer for part 1 Mass of the saltwater (in kg)Answer for part 2 Quantity (Volume) of saltwater (in m3) Answer for part 3
A shell-and-tube heat exchanger is used to cool compressed liquid methanol from 176 °F to 104 °F. The methanol flows on the shell side of the exchanger. The coolant is water that rises in temperature from 50 °F to 86 °F and flows within the tubes at a rate of 68.9 kg s-1. Finding the appropriate thermophysical data and applying the proper equations, you are required to do the following:
determine the value of AB. Water is to be heated from 20°C to 70°C as it flows through a 40 mm internal diameter and 600 mm long tube. The outer surface of the tube is wrapped with electrical wire which acts as an electrical resistance heater. The heater provides uniform heat flux throughout the surface of the tube. The outer surface of the heater is well insulated. At steady state if the system provides hot water at 0.2475 kg/s, determine the power rating of the resistance heater and the inner surface temperature of the pipe at the exit. Р = 990 kg/m³; k = 0.631 W/(m K); c Pr-4.328 = 4180 J/(kg K); v = 0.66 x 10-6 m²/s: