In case of emergency, the gas actuator is used to move a50-kg block B by exploding a charge C near apressurized cylinder of negligible mass. As a result of theexplosion, the cylinder fractures and the released gasforces the front part of the cylinder, A, to move B forward,giving it a speed of 200 mm/s in 0.4 s. (Figure 1)FigureB<VB 200 mm/sB1 of 1 >Part AIf the coefficient of kinetic friction between B and the floor is μ = 0.5, determinethe impulse that the actuator imparts to B.Express your answer to three significant figures and include the appropriateunits.I = 20SubmitMÅN sPrevious Answers Request Answer< Return to AssignmentX Incorrect; Try Again; 3 attempts remaining?Provide Feedback

Answered: Image /qna-images/answer/e54b8c94-a930-47c4-a301-49915905b8cb.jpg

In case of emergency, the gas actuator is used to move a 50-kg block B by exploding a charge C near a pressurized cylinder of negligible mass. As a result of the explosion, the cylinder fractures and the released gas forces the front part of the cylinder, A, to move B forward, giving it a speed of 200 mm/s in 0.4 s. (Figure 1) Part A If the coefficient of kinetic friction between B and the floor is μ = 0.5, determine the impulse that the actuator imparts to B. Express your answer to three significant figures and include the appropriate units. O μA ?

In case of emergency, the gas actuator is used to move a 50-kg block B by exploding a charge C near a pressurized cylinder of negligible mass. As a result of the explosion, the cylinder fractures and the released gas forces the front part of the cylinder, A, to move B forward, giving it a speed of 200 mm/s in 0.4 s. (Figure 1) Part A If the coefficient of kinetic friction between B and the floor is μ = 0.5, determine the impulse that the actuator imparts to B. Express your answer to three significant figures and include the appropriate units. O μA ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. A 2-kg sphere is attached to a massless rigid rod attached to a fixed pivot point O. The rigid rod and mass rotate in the horizontal plane. A moment is applied to the rod of magnitude M = 0.5t² N. m, where t is in seconds. The length of the rod is 0.5 m. Determine the speed of the sphere after the moment is applied for 5 seconds. M(t)
4. 4000-lb car A traveling north at 30 mph through an intersection is t-boned by 3500-lb car B traveling east. The two cars became stuck together and skidded in a direction 35 degrees north of east. Determine velocity of car B upon impact.
The 25-kg block A rests on the 60-kg plate B as shown in (Figure 1). Figure B 30° 0.5 m PAB=0.2 Mac = 0.1 >
A sled weighing 100 lb reaches the foot of a hill with a speed of 40 ft/s. The coefficient of kinetic friction between the sled and the horizontal surface of the ice at the foot of the hill is 0.03. Determine the force exerted by the sled.
(e) Two blocks X and Y are connected by a light and inextensible string as shown in the figure below. The string passes over a light and smooth pulley. Block Y has a larger mass than block X. Assuming that the friction between block Y and the inclined plane is negligible, describe and explain the motion of the two blocks when the blocks are released. 30 deg
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A 75-Mg boxcar A is moving in a railroad switchyard with a velocity of 12.5 km/h toward cars Band C, which are both at rest with their brakes off at a short distance from each other. Car Bis a 30-Mg flatcar supporting a 40-Mg container, and car Cis a 70-Mg boxcar. As the cars hit each other, they get automatically and tightly coupled. v km/h A C В NOP Determine the velocity of car A immediately after each of the two couplings, assuming that the container slides after the first coupling but hits a stop before the second coupling occurs. km/h →. The velocity of car A after the first coupling is | The velocity of car A after the second coupling is km/h +.
Dyanmics Engineering review Part B Determine the normal force of the rod on the collar at B. Express your answer to three significant figures and include the appropriate units. N = Part C Determine the rate of increase in collar's speed at B. Express your answer to three significant figures and include the appropriate units. a =
(a) A car of weight 600 N is at rest. Another car of weight 420 N body moving to the left with a velocity of 12 m/s collides with the car which is at rest . After impact the car which is moving before impact comes to rest. Find the final velocity of body after impact and the coefficient of restitution. (b)A vehicle of mass 13 tonnes runs into a buffer stop having three buffer springs connected in parallel each of 1150 kN/cm, 2850 kN/cm and 1350 kN/cm stiffness respectively. Find the maximum compression of the springs, if the truck is travelling at 65 km/hr. Also calculate the load acting on the spring.
A bullet (W₁ = 3.5 oz) with a is fired horizontally with a velocity v₁ = 1675 ft/sec into the block (W₂ = 5.7 lb) of soft wood initially at rest on the horizontal surface. The bullet emerges from the block with the velocity v₂ = 1280 ft/sec, and the block is observed to slide a distance of d = 7.3 ft before coming to rest. Determine the coefficient of kinetic friction μk between the block and the supporting surface. Answer: Uk= i W₁ W₂
2. Block 1 of mass m, slides from rest along a frictionless ramp from height h = 1.60 m and then collides (completely inelasticly) with stationary block 2 of mass m2 = 3.00 m.. After the collision, the two blocks slide into a region where the coefficient of kinetic friction is µx = 0.300 and come to a stop in distance d within that region. a) What is the speed of m, when it reaches the bottom of the ramp? b) What is the speed of the combination of the two blocks after the collision? c) What is the value of distance d?
A 74 g ball B dropped from a height ho=1.9 m reaches a height h₂= 0.25 m after bouncing twice from identical 250-g plates. Plate A rests directly on hard ground, while plate Crests on a foam-rubber mat. ho B hy Determine the height h1 of the ball's first bounce. The height h1 of the ball's first bounce is m.
Question 3: Objects A and B are connected by a rope with fixed length of 7 ft. They start moving from rest at x = 0, being pulled by the constant 20-lb force. If the coefficient of kinetic friction 4 is 0.2 between both objects A, B and the contacting surface, what is the speed of object B when x = 4 ft? Neglect the friction at the pulley. WB= 20 lb B 3 ft x = 4 ft 20 lb W 12 lb