In an impulse turbine, the steam enters the wheel through a nozzle with a velocity of 500 m/s and at an angle of 20° to the direction of motion of blade. The blade speed is 200m/s and the exit angle of the moving blade is 25°. The work done per kg of steam is..

In an impulse turbine, the steam enters the wheel through a nozzle with a velocity of 500 m/s and at an angle of 20° to the direction of motion of blade. The blade speed is 200m/s and the exit angle of the moving blade is 25°. The work done per kg of steam is..

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A reservoir is at effective height of 95m. An irreversible pump is used to pump a mass flow of 4500 kg/s of water from ground level into the reservoir. Consider water as an incompressible liquid with mass density of 1000kg/m . 1) What is the power consumption of pump for an isentropic pump efficiency of 82%? 2) What is the power that can be recovered from a turbine with 93%? (with the same mass flow and height). 3)What is the change in temperature of the pumped water?
Solve it correctly please. I will rate accordingly with 3votes.
Air with a density of 2.21 kg/m3 enters a nozzle with inlet cross sectional area of 80 cm2, the inlet velocity is 20 m/s, then the mass flow rate of air through the nozzle is: Select one: a. 0.35 b. 0.53 c. 0.40 d. 0.31 e. none of the mentioned
= (a) A centrifugal pump, with salt water as the working fluid, has the impeller blades rotating at 750 rpm. The fluid enters the blades in the radial direction, i.e. at an angle of α₁ = 0°, and exits the blades at an angle of 35° from the radial direction. i.e. α₂ = 35⁰. The inlet radius and blade width are r₁ 12.0 cm and b₁ = 18.0 cm, respectively. The outlet radius and blade width are 1₂ = 24.0 cm and b₂ = 16.2 cm, respectively. Assuming 100 percent efficiency, and if the volumetric flow-rate through the pump is 0.573 m³/s, compute the net head produced by the centrifugal pump. Furthermore, calculate the required brake horsepower in Watts. Take the density of salt water to be p 998.0 kg/m³. =
Steam turbine with 1.5kg / s mass flow, 6MPa pressure, 500C temperature and 20 m / s speed is entering. The pressure at the outlet is 0.5MPa, the speed is 75 m / s and the degree of dryness is 0.95. Turbine power If its output is 2500kW, calculate the heat transfer from the turbine per unit time.
Calculate the thrust of a turbojet engine with an inlet diameter of 4 ft. If an airplane is flying at altitude of 15km at Mach 0.8 with an exit velocity of 900ft/s. The turbojet engine thrust at 15-km. (in Lbf)
Steam at 1 kg / s mass flow enters a steam isentropic turbine at a pressure of 4 MPa, a temperature of 300ºC and a speed of 50 m / s, and leaves it at a pressure of 150 kPa and a speed of 200 m / s. .Note: T0 = 25 ºC, P0 = 100 kPa, T (K) = 273 + ºC a) Find the power produced by the turbine.b) Find the reversible power produced by the turbine.c) Find the isentropic efficiency of the turbinec) Find the second law efficiency of the turbine.
in a steam turbine, the steam enters the wheel through a nozzle with velocity of (520m/sec) and at angle of (20°) to the direction of motion of the blade. The blade speed is (210m/sec)and the exit angle of the moving blade is (27°). Find (a) the inlet angle of the moving blade, (b) exit velocity of steam and its direction (c) the work done per kg of steam (d) the blade efficiency. Draw the velocity diagram for the moving blade.
Nitrogen at a flow rate of 0.1 kg / s enters a heat exchanger at a temperature of 450 K and 320 It comes out at K temperature. The other fluid of the heat exchanger is water, it enters at 20 ° C and leaves at 35 ° C. a) Calculate the flow of water. b) Calculate the entropy generation in this heat exchanger. (Take the average specific heating heat for nitrogen as 1.042 kJ / kgK.)