in a test to determine the discharge coefficient of a 60 mm x 15 mm Venturi meter, the total weight of water passing the meter in 5 minutes was 350 kg. A mercury differential gauge connected to the inlet and throat of the meter showed an average mercury difference during that time of 360 mm. Calculiate the meter coefficient. Round off your answer to ane decimal place. Answer: Cv

in a test to determine the discharge coefficient of a 60 mm x 15 mm Venturi meter, the total weight of water passing the meter in 5 minutes was 350 kg. A mercury differential gauge connected to the inlet and throat of the meter showed an average mercury difference during that time of 360 mm. Calculiate the meter coefficient. Round off your answer to ane decimal place. Answer: Cv

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An Analysis of water from a surface stream yields the following results Ca+2=60mg/L HCO3-=115mg/L Mg+2=10mg/L SO4-2=96mg/L Na+=7mg/L NO3-=10mg/L K+=20mg/L CI-=11 mg/L If an error of 10 percent is acceptable, should the analysis be considered complete?
i need the answer quickly
A fluid flows through a 100 mm long, 4 mm diameter glass tube. In 10 minutes 0.0013 cubic meters of fluid passes through the tube. If the head loss is 1 meter, what is the Reynolds number? Assume the flow is laminar
Mr.X performs the laboratory test and determines that 12 mg/l of alum dose is required to treat the water. What is the quantity of alum required to treat 14 million liters of water per day at a treatment plant. Also determine the amount of carbon dioxide gas produced per liter of water during treatment. B I U GGG 25 85 ET M 69
Water Gs=1 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter, the total weight of water passing through the meter in 5 minutes was 3.5 kN. A mercury differential gage connected to the inlet and throat of the meter showed an average mercury difference during that time of 300 mm.. Determine the actual discharge if the same meter is used later on and a 250 mm difference is then observed. Mercury, Hg Gs = assume, 4 significant figures 2. The diameter of a 3 meter pipe decreases from 450 mm to 150 mm. If the velocity is to decrease uniformly in a linear manner, draw the diameter profile at each 500 mm length interval along the pipe. Discharge is 150 liters per second. Reservoir B 3. A pump draws water at 300 liters per second from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1 is 20 times the velocity head in the 200 mm diameter and the head loss from 2 to B is 20 times the velocity head in the 150-mm diameter pipe. Assume your…
Q9: In a test on a two- stroke, heavy oil, marine engine, the following observations were made, Oil consumption, 4.05 kg; Calorific value of oil, 43000 kj/kg; het brake load 579N; Mean brake diameter, 1 m; mean effective pressure 275 kN/ m2; Cylinder diameter 0.20m; stroke, 0.250m; speed, 360 rpm. Icalculate o @ the mechanical efficiency the indicated thermal efficiency O Ihe brake thermal efficiency and The quantity of jacket water required per minute if 30% of the energy supplied by the fuel is absorbed by this water daisl a zgaus Permissible rise in temperature is 20k and specific heat capacity of water=D4.1868
Problem 4. A receipt of surface water sample is given in Table below: Substance Concentration (mg/L) Total Hardness 1000 mg/L CaCO3 Phenolphthalein acidity 5 mg/L CaCO3 Phenolphthalein Alkalinity 3 mg/L CaCO3 It is known that phenolphthalein alkalinity is only due to CO3²- and phenolphthalein acidity is only due to H₂CO3. Assuming the hardness of sample is because of calcium and magnesium ions, alkalinity-acidity are due to the carbonate species, calculate: a) The pH of sample. b) Temporary and permanent hardness as mg/L CaCO3. c) Total alkalinity and acidity as mg/L CaCO3. Molecular weights (g/mole): Ca = 40, Mg = 24, H = 1, C = 12, 0 = 16
Task 3: Fluid Mechanics Lab Meters You studied the SAYBOLT viscometer in the fluid mechanics lab to determine 20W50 Motor Oil viscosity. Follow the following steps to do your task. HEATING UNIT THERMOMETER LIQUID BATH Fluid CONTAINER 60 cC CORK ŘESERVOIR Figure 4: Schematic for SAYBOLT viscometer. a) Illustrate the results of the viscosity test of the above motor oil then fit the viscosity function of temperature to the following logarithmic quadratic correlation as described below. Find the values for the constants a, b, and c. Take Ho at T, = 0°C. a + b| + T Mo b) What is the viscosity of the used motor oil at 280 K, 305 K and 320 K? You can use the above equation
Figure 1 of 1 Pgas A U h₁ B mercury Part C Assume Patmos = 1.00 atm. What is the gas pressure Pgas? Express your answer in pascals to three significant figures. Ο ΑΣΦ Pgas h₂ Submit Hints My Answers Give Up Review Part Incorrect; Try Again; 2 attempts remaining ? Pa
T Water Gs=1 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter, the total weight of water passing through the meter in 5 minutes was 3.5 kN. A mercury differential gage connected to the inlet and throat of the meter showed an average mercury difference during that time of 300 mm. Determine the actual discharge if the same meter is used later on and a 250 mm difference is then observed. h = 300 mm Mercury, Hg Gs = assume, 4 significant figures 0