EA two-stage distiller system is used to remove TDS from sea water as shown in the figure. The concentration of IDS (mg/) in the brine leaving Stage 2 distiller is: Stea Stage 2 Q4 MGD Brine Sea water Q 13 MGD TDS-38000 Frosh water Q11 MGD TDS- 70 mg Heat Heat (ii) 123,308 ad from the giyen information (iv) 246,615 (vi) none of the above (i) 332,615 (ii) 170,615

EA two-stage distiller system is used to remove TDS from sea water as shown in the figure. The concentration of IDS (mg/) in the brine leaving Stage 2 distiller is: Stea Stage 2 Q4 MGD Brine Sea water Q 13 MGD TDS-38000 Frosh water Q11 MGD TDS- 70 mg Heat Heat (ii) 123,308 ad from the giyen information (iv) 246,615 (vi) none of the above (i) 332,615 (ii) 170,615

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: I have an equalization tank with the following dimensions: Tank Dimensions: Height: 5.15 meters…

Q: In a titration of dilute sulfuric acid, H2SO4, with sodium hydroxide, NaOH, how many milliliters…

A: The chemical reaction is given as H2SO4 (aq) + 2NaOH(aq) --> Na2SO4(aq) + 2H2O(l)

Q: The PureNSafe Company is designing a solar-driven, portable water disinfection system to be used by…

A: Disinfection rate constant for UV light (k)= 7.50 s-1The required reduction in bacterial countc= 3.5…

Q: Available chlorine in bleaching powder solution is 0.5mg/ml. To obtain a chlorine dose of 0.1 mg/1…

Q: Small droplets of carbon tetrachloride at 68 °F are formed with a spray nozzle. If the average…

A: The diameter of the carbon tetrachloride droplet,To determine the pressure difference between the…

Q: Convert the concentration of SO2 from 80 pg m temperature of 25°C and a pressure of 101.325 kPa. to…

A: ppm = Conversions are needed to calculate the volume of So2 in cubic meters.

Q: Solids analyses were conducted on a soybean processing wastewater. 50 ml of wastewater is used for…

A: Given, Volume of sample (V)=50 mL for total solid analysis Volume of sample (V-)=100 mL for…

Q: Q4. At 20°C, hydroxyl ion (OH) concentration of a solution is 10-5.5 M. The pH of that solution is…

Q: The surface water with 6000 m³/d of flow rate will be treated for hardness removal using lime-soda…

A: The steps to solve this are: 1. Find total hardness and ALkalinity 2. Find Carbonate hardness and…

Q: 4. Calculate the Reynolds Number for 6-inch (diameter) production tubing assuming West Texas Crude…

A: Since; Q1 = 500 STB / day = 5005.434 * 105=9.20*10-4 m3 /s

Q: Convert the following from milligrams per liter as the ion or compound to milligrams per liter as…

A: Concentration in mg/L are given. We need to calculate concntration as mg/L CaCO3

Q: Text - Problem 2.56] (Show your answer in ppmv as well as ppbv.) 56 Convert the concentration of SO₂…

Q: Disinfection of 20 MLD water is done with 30 kg chlorine to achieve 99% efficiency in a contact time…

Q: Q1: A conventional ASP is to be used for treatment of 10,000 m³/d of municipal wastewater. The…

Q: What are the responsibilities of a project manager of a design-build work?

A: A project manager is a person, who has the whole project responsibility from the successful…

Q: The solids content of a stream water sample is to be determined. The total solids content is…

Question

EA two-stage distiller system is used to remove TDS from sea water as shown in the figure. The
concentration of IDS (mg/) in the brine leaving Stage 2 distiller is:
Stea
Stage 2
Q4 MGD
Brine
Sea water
Q 13 MGD
TDS-38000
Frosh water
Q11 MGD
TDS- 70 mg
Heat
Heat
(ii) 123,308
ad from the giyen information
(iv) 246,615
(vi) none of the above
(i) 332,615
(ii) 170,615

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution:-

VIEW

Step 2 Solution:-

VIEW

Step 3 Answer:-

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need solution on page plz
2. Families in a community in a developing country use large, 200.0 L drums to un-treated surface water. You are designing a device that is designed to dose the volume with a coagulant, stir to allow flocculation, then add chlorine tablets to disinfect the water. The water is 25 °C and initially contains 1.0E+09 particles per L. The initial particles can be assumed to be spherical, 15.0 micrometers in diameter, and with a density of 1.675 g/mL. a. If the drums have a diameter of 572 mm, how long will it take for the particles to completely settle without any coagulation or flocculation? (answer in seconds) You have determined that you can achieve complete destabilization of particles by achieving an ionic strength of 0.01 M or higher. If you use alum (Al2(SO4)3) as a coagulating agent, what mass of alum must be added per batch of 200 L? (answer in grams) How many joules of energy would be required to stir the drum at a mixing intensity of 150 s-' for 20 minutes? If the drum is stirred…
Calculate the BOD concentration based on the data below. DOinitial (mg/L) 7 DO final (mg/L 3.5 Vol. sample (ml) 15 Vol. dilution (ml) 285 BOD (mg/L) ?
BOD of a wastewater sample is determined by incubating the BOD bottles at four different temperatures, 5, 15, 20, 35, and 50°C. i The ultimate BOD of the sample incubated at 10°C would be-----compared to the sample at 50°C. ii. The reaction rate constant, k for sample incubated at 35°C would be- compared to the sample incubated at 5°C
Part d
Small droplets of carbon tetrachloride at 68 °F are formed with a spray nozzle. If the average diameter of the droplets is 280 µm what is the difference in pressure between the inside and outside of the droplets? Pa
Mr.X performs the laboratory test and determines that 12 mg/l of alum dose is required to treat the water. What is the quantity of alum required to treat 14 million liters of water per day at a treatment plant. Also determine the amount of carbon dioxide gas produced per liter of water during treatment. B I U GGG 25 85 ET M 69
Small droplets of carbon tetrachloride at 68 °F are formed with a spray nozzle. If the average diameter of the droplets is 300 μm what is the difference in pressure between the inside and outside of the droplets? Pa
For an electrostatic precipitator of given geometry and operating conditions, the collection efficiency for 2 micrometer particles is 99.90 percent. On the basis of a Deutsch-type equation for efficiencies, estimate the collection efficiency for (a) 1 micrometer and (b) 0.5 micrometer particles
CHAPTER 5 Q7. Determine the lime storage volume required for the following conditions: Average water demand = 0.18 m3/s Maximum dosage = 200 mg/L as CaO Shipping time = 1 week Lime is an interruptible chemical Assume the bulk density and purity of lime is the average of the values given in Table 7..
Problem 2: Engineers sometimes use pipes as reactors in treatment plants. Suppose that the plant flow is 3.3ft3/s (about 2.1 million gallons per day, mgd) and a cylindrical pipe is to be used for disinfection.A. Draw a sketch of the system. Indicate the control volume by a dashed line. What kind of hydrodynamicmodel should you use for a pipe? What mixing conditions should you assume?B. Write the integrated mass balance equation for the pollutant in symbols at steady state. (“Integrated” meansthat your mass balance looks like: C = …) Define your symbols.C. For a pipe 3.5 feet in diameter and 50 feet long, what is the hydraulic residence time in minutes?D. For the pipe in Part C, what value of the first-order rate constant (in min–1) is needed to achieve a 99% removal of bacteria?
*