In a spring controlled governor, the radial force acting on the balls was 4500 N when the center of the balls were 200 mm from axis and 7500 N when at 300 mm, assuming that the force varies directly as the radius, find the radius of the ball path when the governor runs at 270 r.p.m. Also find what alternation in spring load is required in order to make the governor isochronous and the speed at which it would then run. The mass of each ball is 30 ka

In a spring controlled governor, the radial force acting on the balls was 4500 N when the center of the balls were 200 mm from axis and 7500 N when at 300 mm, assuming that the force varies directly as the radius, find the radius of the ball path when the governor runs at 270 r.p.m. Also find what alternation in spring load is required in order to make the governor isochronous and the speed at which it would then run. The mass of each ball is 30 ka

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need a clear and fast answer within 20 minutes. Thank you
Example The bob of a 2-m pendulum describes an are of circle in a vertical plane. If the tension in the cord is 2.5 times the weight of the bob for the position shown, find the velocity and the acceleration of the bob in that position. SOL
A block of mass m₁ is suspended from the ceiling with a spring k and damper b. Attached to the block is a massless rod of length L. Affixed to the end of the rod is a point-mass of mass m₂. Gravity is acting in the direction indicated in the figure. Use the energy method to set up the energy expression you would use to calculate the equations of motion for the system. Hint: be sure to decompose the velocity of the pendulum into horizontal and vertical components. DO NOT CALCULATE THE EQUATIONS OF MOTION, only setup the energy expression. x(t) b 7 m₁ e(t) (m₂
23. In a spring controlled governor, the radial force acting on the balls was 4500 N when the centre of balls was 200 mm from the axis and 7500 N when at 300 mm. Assuming that the force varies directly as the radius, find the radius of the ball path when the governor runs at 270 r.p.m. Also find what alteration in spring load is required in order to make the governor isochronous and the speed at which it would then run. The mass of each ball is 30 kg. 80 mm 60 mm A 80 mm stor lo auiber ors +a b-
Please answer quickly. Thanks
The figure shows a schematic of a simple Watt governor mechanism with the spindle 0102 rotating at an angular velocity w about a vertical axis. The balls at P and S have equal mass. Assume that there is no friction anywhere and all other components are massless and rigid. The vertical distance between the horizontal plane of rotation of the balls and the pivot O₁ is denoted by h. The value of h = 400 mm at a certain w. If w is doubled, the value of h will be mm. (0) g = 9.8 m/s₂ h Spindle O Q Sleeve (QR) Cylindrical Joint R S
A box with mass m = 2.75 kg rests on the top of a table. The coefficient of static friction between the box and the table is μs = 0.71 and the coefficient of kinetic friction is μk = 0.34. Write an expression for Fm the minimum force required to produce movement of the box on the top of the table. Solve numerically for the magnitude of the force Fm in Newtons. Write an expression for a, the box's acceleration, after it begins moving. (Assume the minimum force, Fm, continues to be applied.) Solve numerically for the acceleration, a in m/s2.
Learning Goal: Use the general equations of motion for plane motion to determine the initial acceleration of a spool. A spool has an outer radius R = 380 mm, an inner radius r = 210 mm, a mass m = 90 kg, and a radius of gyration KG = 320 mm. A rope is wrapped around the inner radius and pulled to the right as shown in (Figure 1). The coefficient of static friction between the spool and the ground is us = 0.2. The coefficient of kinetic friction is k = 0.15. Figure R A P 1 of 1 Part A Draw the free-body diagram for the spool, assuming the friction force acts to the right. Draw the vectors, starting at the black dots. The location and orientation of the vectors will be graded. The length of the vectors will not be graded. + 0 No elements selected Select the elements from the list and add them to the canvas setting the appropriate attributes. Submit Request Answer
will rate if correct
Torsional springs provide a simple propulsion mechanism for toy cars. When the rear wheels are rotated asif the car were moving backward, they cause a torsional spring (with one end attached to the axle and the other to thebody of the car) to wind up and store energy. Therefore, a simple way to charge the spring is to place the car onto asurface and to pull it backward, making sure that the wheels roll without slipping. Note that the torsional spring canonly be wound by pulling the car backward; that is, the forward motion of the car unwinds the spring.Let the weight of the car (body and wheels) be W = 5 oz, the weight of each of the wheels be Ww= 0.15 oz, and theradius of the wheels be r = 0.25 in., where the wheels roll without slip and can be treated as uniform disks. Neglectingfriction internal to the car and letting the car’s torsional spring be linear with constant kt= 0.0002 ft-lb/rad, determinethe maximum speed achieved by the car if it is released from rest after pulling it…
Show complete solutions. Please draw the figure or the illustrations. Problem:Two horses are pulling a barge with mass 2000 kg along a canal, as shown in the Figure. The cable connected to the first horse makes an angle of 30o with respect to the direction of the canal, while the cable connected to the second horse makes an angle of 45.0o. Find the initial acceleration of the barge, starting at rest, if each horse exerts a force of magnitude 600 N on the barge. Ignore forces of resistance on the barge.