find the magnitude and direction of the acceleration A plate with mass = 6-kg is initially at rest on an ice block (no friction). A force of P 240-N is applied suddenly as shown. The magnitude and direction of the acceleration of point A on the plate is closest to: ICE BLOCK PLATE h=96-cm w=88-cm 0= 52-deg Magnitude Choices= "A" 91.9 "B" 98.6 "C" 105.5 "D" 112.1 "E" 118.8 "F" 125.5 "G" 132.2 "H" 139.0 "I" 145.6 "J" 152.3 m Direction positive x direction) Choices- "A" 103.5 "B" 109.3 "C" 115.2 "D" 121.0 "E" 126.8 "F" 132.8 "G" 138.5 "H" 144.5 "I" 150.1 "J" 155.9 -deg

Q: Determine the maximum shear stress in the solid shaft. The diameter of the shaft is 1 in. Assume the…

A: Given-Data:- Diameter of shaft=1inch No Friction is assumed To-Find:- Maximum Shear Stress

Q: The crankshaft has loads as shown. Determine the vertical (y-direction) reaction of the bearing at…

A:

Q: 1. The scale is used to measure dirt in a hydraulic system. 2. Probably the greatest problem with…

A: According to the given data in the question    We need to fill the blank 1. The ______________…

Q: Determine the magnitude (N) of the force in member BC  if  F=287N , a=0.44m, b=1.97m, r=1.71m and…

A:

Q: The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T =…

A: Given data T = 320 N-m The allowable shear stress for the material is Tallow = 185 MPa.

Q: Write the two equations of equilibrium, EFx = 0 and EFy !3! %3D

A:

Q: Express the quantity 556.2 x 10^-12s in fs.

A: Given Data: The time given is t = 556.2×10-12 s. The conversion of second to femtosecond can be…

Q: 7. 8. is an important part of proper reservoir operation. filters protect a pump from dirt in a…

A: According to the given data 7.________filters protect a pump from dirt in a reservoir. 8.…

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: 120 mm 60 mm 90 mn D 80 mm C 45 mim 480 N

A:

Q: /0.009MA BM FOLE 4. Answer:

A: Geometric Dimensioning and Tolerancing (GD&T) could be a language of symbols and measures…

Q: 4. Use F₁ =3, 6₁ = 2, k₁₂₁ = 4₁ K3 = 2,63 = 1, J₁ = 2₁ J₂=5, find the impulse and step response of…

A: Given: To find: Impulse and step response

Q: I start from 2f₁= max, derive to this expression {fy = may, 2) ap(x, y, z) dx (_ ap(x, y, z) ay

A: For the solution refer below images.

Q: 1. Below on the left you can see a cantilever beam (of structural steel, E = 210 GPa), which is…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: A force F = 6980 N acts upon a piston head, as shown in the figure. The gudgeon pin G connects the…

A:

Q: 3-9. Solve for the algebraic sum of the moments in pound-feet about A when h is 20 m as shown in…

A: Given data h = 20m Forces acting are 800N, 500N

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.