B. 2

Q: The torque of 12kN m is applied to the 6-meter steel shaft's free end. The shaft must rotate at a…

A:

Q: The 60-mm-diameter solid shaft is made of A-36 steel and is subjected to the distributed and…

A: Write the expression of the moment of inertia of the shaft. Write the properties of A-36 steel.

Q: The 54-mm diameter shaft is subjected to the torques as shown. Determine the angle of twist (in…

A:

Q: *10-56. The shaft of radius c is subjected to a distributed torque t, measured as torquellength of…

A: Given data: The length of the shaft is The radius of the shaft is The torque per unit length is The…

Q: If end B of the shaft, which has an equilateral triangular cross-section, is subjected to a torque…

A: Given data as per question Torque = 900 lb.ft Assuming G of the shaft = 3.7×103 ksi

Q: 10-51. The 50-mm-diameter A992 steel shaft is subjected to the torques shown. Determine the angle of…

A: Sign convention for torque: When observed from the right-hand cross-section of the shaft, a…

Q: Determine the shear stress at point A and point B with appropriate units

A: Givendiameter of shaft d=80mmT=500Nm

Q: FI0-5. Determine the maximum shear stress in the shaft at section a-a. G00 N-m -30 mm 1500 N-m 40 mm…

A: The outer radius of the section a-a of the shaft is given as R = 0.04 m. The inner radius of the…

Q: *10-44. The shaft is made of A-36 steel. It has a diameter af 25 mm and is supported by bearings at…

A: Given, Diameter of shaft = 25 mm Radius = 12.5 mm = 12.5x 10-3 m Torque = 90 N.m

Q: The 20-mm-diameter A-36 steel rod is subjected to the axial forces shown. Determine the displacement…

A:

Q: 10-46. The A992 steel shaft has a diameter of 50 mm and is subjected to the distributed loadings…

A: 1iven: To find maximum shear stress Plot a graph for angle of twist

Q: The tapered shaft has a length L and a radius r at end A and 2r at end B. If it is fixed at end B…

A:

Q: The shaft has an outer diameter of 1.5 in. and an inner diameter of 0.8 in. If it is subjected to…

A:

Q: The 80-mm-diameter shaft is made of steel. If it is subjected to the uniform distributed torque,…

A: Given Data: The length of the shaft is L = 800 mm. The uniformly distributed torque acting on the…

Q: 2-3. The rigid beam is supported by a pin at A and wires BD and CE. If the load P on the beam causes…

A:

Q: The rod is pinned at its end A and attached to a torsional spring having a stiffness k, which…

A:

Q: The shaft is subjected to the vertical and horizontal loadings of two pulleys D and E as shown. It…

A: Draw the free body diagram in the xy plane.

Q: 10-57. The tubular drive shaft for the propeller of a hovereraft is 6 m long. If the motor delivers…

A: Given Data The power of the motor is: P=4 MW=4×106 W The angular velocity is: ω=25 rad/s The…

Q: The 80-mm-diameter shaft is made of steel. If it is subjected to the triangular distributed load,…

A: Given Data Uniformly distributed torque is: T=15 kN·m/m Total length of the shaft is: L=1000 mm=1 m…

Q: The solid and hollow shafts are each subjected to the torque T. In each case, sketch the shear…

A: The solid shaft is subjected to torque T in a clockwise direction. The shear stress is calculated…

Q: The long bolt passes through the 70.4-mm-thick plate. If the force in the bolt shank is 9.5 KN, then…

A: The thickness of the plate:Diameter of the cylinderical area:Force applied:

Q: The shaft is fixed to the wall at A and is subjected to the torques shown. Determine the maximum…

A: Consider a point D between points B and C. Calculate the internal torque in section CD of the shaft.…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.